Universal Clutch Alignment Tool
For single plate clutches.
Suitable for flywheels with or without pilot bearing.
Fast to fit and remove with universal applications.
Collet Sizes : 14mm to 28mm across 3 adaptors.
Cone size range : 35mm - 67mm.

Jaguar / Land Rover Clutch Alignment Tool
To hold the clutch centre plate centred on the
flywheel while fitting the clutch cover plate.
Applicable to Ford Duratorq Diesel Engines

17pc Universal Clutch Aligning Kit
For alignment of flywheel pilot hole and clutch drive plate
Precision manufactured steel bushes with chemically blacked finish
Suitable for most cars and light commercial vehicles

10pc Clutch Alignment Tool Set
Complete with 8 adaptors
Cone : 20.5 x 82mm long
Sizes : 11 | 12 | 15 | 17 | 19 | 20 | 21 | 25 mm.
Tapered cone aids clutch plate alignment
For Aligning single disc clutches on most vehicles.

11pc Clutch Alignment and Adjustment Tool Set
Suitable for a wide range of vehicles and some light commercial vehicles.
Screw action provides fast adjustment for required hub diameter.
8 interchangeable spigot adaptors aid close alignment.
Adaptors : 12 | 14 | 15 | 16 | 17 | 18 | 19 | 20mm diameter.
Expanding mandrels : 15 - 19mm | 20 - 26.6mm | 23 - 36mm diameter.

Audi Clutch Alignment Tool
For alignment and installation on the workbench.
Suitable for front wheel drive vehicles
without pilot bearing in the flywheel.
3 different size expanding collets.
Small cone - 15mm
Medium cone - 19mm
Large cone - 24mm

Clutch Alignment Tool Kit
For clutch discs with 15 to 28 mm clutch hubs.
Provides accurate centring of the clutch disc
on most vehicles with or without pilot bearing.
Alignment according to friction surface of the clutch pressure plate.
Centring sleeve diameter : 12 | 14 | 15 | 16 | 17 | 18 | 19mm

Release Shaft / Guide Rail Bolt Puller
For extracting the clutch release shaft on the Fiat Ducato with pulling clutch.
Required for clutch replacement and gearbox repair on 1994 models.
Includes puller body with M8 x 1.25 internal spindle thread pull Clamp.
Also for extracting the chain guide rail bolt on BMW and Mercedes engines.
M6 x 1.0 bolt for removing the guide rail bolt

DCT Wet Clutch Oil Seal Fitting Kit
For Ford and Volvo vehicles fitted with the Dual Wet Clutch System
also vehicles with Getrag MPS6 / 6DCT 450 gearboxes.
Includes the seal guide and cover press used for
the fitting of the clutch cover without damaging the centre seal.
OEM Codes : 308-764 | 308-783 | 9997383 | 9997388.

Dual Clutch Oil Seal Remover / Installer Set for Ford
Specially designed to remove and install input shaft and
differential seals on Ford 6 speed dry plate dual clutch gearboxes.
Seal Ring Puller for inner input shaft
Seal Ring Guide for inner / outer input shaft
Seal Ring Press Tool for inner / outer input shaft
Seal Ring Press Tool for drive shaft
Gearboxes : DPS6 | 6DCT250

Ford Dual Clutch Reset Tool Set
Designed to reset the twin clutch pack fitted to
Ford 6 speed DPS6/6DCT250 transmissions.
Applicable to :
Transit Connect from 2014
Fiesta from 2008
Focus from 2010
B-Max from 2012

DSG Dual Clutch Transmission Tool Kit
Ford Focus DCT Dual Clutch Transmission DPS6
Specially designed to disassemble and install dry transmissions
It re-springs / re-trips the springs on the clutch so that you can reinstall it again.
Fiesta 2011 - 2019
Focus 2012 - 2018
Transit Connect 2019
B-MAX since 2012
OEM Code : 307675

Twin-Clutch Dry Transmission Remover / Installer
For servicing the transmission and alignment of the twin clutch when changing the oil seal.
Applicable to : Ford and Volvo transmission DPS6.
OEM Code : 307675

Audi / VW 7 Speed DSG Clutch Installer / Remover
For the installation and Removal of the Clutch or Gearbox
Applicable to Audi / VW 7 speed vehicles similar to
conventional single disc clutches the dry double clutch
is also located in the gearbox housing

Dual Clutch Transmission Tool
For 6 speed DCT - Dual Clutch Transmission
Applicable to : Ford focus | C-Max | S-Max | Galaxy | Mondeo | Kuga
Volvo C30 | C70 / 06 | S40 / 04 | S60 / 11 | S80 / 07 | S80L |
V40 /13 | V40 Cross Country | V50 | V60 | V70 / 08 | XC60
Also Dodge Avenger and Journey plus Chrysler Sebring.

DSG Clutch Bearing Gauge Block Tool
For checking and adjusting the position of clutch bearings
in automatic 7 speed / DSG gearboxes with dual clutch.
Applicable to Volkswagen / Audi vehicles from 2011 onwards.
Suitable for use with CT0500 VAG DSG Clutch Installation Kit
OEM Code : T10466

For Removing the DSG Gearbox ECU / mechatronic control module
Audi / VW 7-speed
Specially designed to remove load from plungers of the mechatronic unit
when you insert the tool between clutch lever and gear housing.
Applicable to : Audi / VW 7-speed dual clutch gearbox. Ideal for use in conjunction with CT0500

Self Adjusting Clutch Mandrel Kit for BMW Vehicles
Mandrel kit for centring the clutch disc on the flywheel during installation.
Can also be used to align new and previously pre-tensioned SAC clutches.
Applicable to BMW vehicles.
Sizes : 15mm x 23mm | 26.5mm | 28mm | 32.5mm | 34mm.
Centring Sleeve : 15mm | 32.5mm.

SAC Clutch Alignment Tool Set
For pre-tensioning self adjusting clutches before removal or installation.
Features a refitting tool to allow the clutch adjuster to be wound back.
Includes a selection of clutch plate and spigot alignment adaptors.
Clutch plate adaptors : 17 - 33.9mm
Spigot adaptors : 13.9 - 21.9mm.
Assembly flywheel threads

SAC Clutch Tool Set
For assembling and fitting Self Adjusting Clutches
on Audi / BMW / Fiat / Mercedes / Renault / Vauxhall / Opel and Volvo.
Avoids clutch plate distortion due to incorrect fitting
and subsequent vibration and shortening of clutch life.

Automatic Transmission Clutch Spring Compressor
Adjustable tool for removing or installing the snap ring
on a transmission rear clutch Piston.
It applies pressure to the clutch drum retaining washer
to compress Piston return springs.
For use on most American cars and light trucks.

Automatic Transmission Clutch Spring Compressor
4 Leg Capacity : 64mm to 175 mm Diameter.
For replacement of rear transmission clutch Piston snap ring.
Adjustable legs fit most cars and trucks.

Flywheel Puller - M26 x 1.5 RH Thread Male
Required to service the flywheel on a large number of Motorbikes
including: Honda / Yamaha / Kawasaki and Suzuki 2 / 4 Stroke Engines

10pc Motorcycle Flywheel Puller Set
used to separate flywheel from the crankshaft taper.
Suitable for most makes of motorcycle.
Left and Right hand thread

BMW Flywheel Tool Set
For Diesel and Petrol chain drive engines.
Found on most BMW K | M | N models
The tool can also be used to hold the flywheel when
removing the timing chain for cylinder head work.

Flywheel Locking Tool
For locking the flywheel via the starter motor aperture.
on Hyundai and Kia vehicles with petrol engines from 2007 to 2018.

Fast Fit Micro Puller 19 - 45mm
Supplied with thrust shaft extension
Capacity : 1 ton
Reach : 73mm
Puller Reach : 19 - 73mm / Min-Max
Puller Spread : 19- 45mm / Min-Max
Designed for the fast and safe removal of small bearings.
Also alternators / generators / domestic appliances / power tools and pumps.
Spring loaded and drop-forged legs are secured around the bearing or gear
by a screw collar to prevent slipping and subsequent damage or injury.

Gear Puller - 3 Jaw
8in. / 200mm
Reversible Legs

5 Ton Gear Puller
with Ratchet Action Legs
for One Man Operation
Capacity : 5in.- 8in. / 125 - 200mm

5 Ton Gear Puller Set
2 and 3 Way Short and Long Legs
Legs now with Ratchet Action
Short Legs : 4in.- 5in. / 100 - 125mm
Long Legs : 5in. - 8in. / 125 - 200mm
Chrome molybdenum -
Legs and Forcing Screw.

Gear Puller Set
with 2 and 3 Leg variations
Legs 3 | 4 | 6 | 8in. Long
Legs 75 | 100 | 150 | 200mm

Universal Puller Set
2 Leg / 3 Sizes
Variable Width
Chrome Molybdenum
Legs - 100 / 200 / 250mm Long

Puller Set - Universal 3 Arm
Puller set with different Leg Lengths for confined spaces
2 Leg Sliding Bar
3 Leg Sliding Bar
Arms - 100 / 200 / 250mm x 3
Spindles - 160 / 270mm Long.

Heavy Duty Hydraulic Puller Set
for removing Gears / Bearings and Sprockets

5 Ton Hydraulic Gear Puller
6 Way 2 and 3 Leg Configuration
Up to 10 Ton Capacity

5 Ton Hydraulic Gear Puller
Maximum Capacity : 5T
Maximum Horizontal Pull Distance : 200mm
Maximum Vertical Pull Distance : 140mm
Axis Stroke : 50mm
Suitable for pulling hubs / flanges / gears and bearings.
Equipped with 3 reversible jaws suitable for different needs.

10 Ton Hydraulic Gear Puller
Maximum capacity : 10T
Maximum Horizontal Pull Distance : 250mm
Maximum Vertical Pull Distance : 160mm
Axis Stroke : 50mm
Suitable for pulling hubs / flanges / gears and bearings.
Equipped with 3 reversible jaws suitable for different needs.

30 Ton Hydraulic Gear Puller
Maximum capacity : 30T
Maximum Horizontal Pull Distance : 400mm
Maximum Vertical Pull Distance : 250mm
Axis Stroke : 75mm
Suitable for pulling hubs / flanges / gears and bearings.
Equipped with 3 reversible jaws suitable for different needs.

50 Ton Hydraulic Gear Puller
Maximum capacity : 50T
Maximum Horizontal Pull Distance : 500mm
Maximum Vertical Pull Distance : 400mm
Axis Stroke : 75mm
Suitable for pulling hubs / flanges / gears and bearings.
Equipped with 3 reversible jaws suitable for different needs.

Ford 5th Gear Puller
Fast and simple method of removing the fifth gear
on front wheel drive transmissions before carrying out internal repairs.
The split collar and retaining sleeve ensures a safe and positive location.
Applicable to : Fiesta / Focus / KA / Mondeo / C-Max / Galaxy and Transit Vans.

2pc Lever Set
Ideal for clutch and transmission work - also
separating ball joint connections on shifter cables & shift linkages.
Plus axle components / ball joint connection points / exhaust hangers
silent blocks / bushes and many panel types and stuck components
Large Lever / Internal dimensions : 25 x 110mm.
Small Lever / Internal dimensions : 15 x 65mm

16pc Slide Hammer / Puller Set
Combination Puller with 5lb Malleable Steel Slide Hammer
Drop Forged Steel Pullers and Attachments
Converts to 2 or 3 Jaw Internal / External Pullers