BMW / Mini / PSA Timing Tool Set
For timing 1.4 & 1.6 Valvetronic direct injection chain drive petrol engines
fitted in BMW Mini / Citroen and Peugeot vehicles.
With Camshaft Locking Tools
Camshaft Alignment Clamp and Crankshaft Setting Pin.
M6 Setscrews Chain Tensioner.
Mini Cooper / Coupe | Citroen C4 | Peugeot 207 / 308 / 3008 / 5008

Chrysler Timing Tool Set
for Chrysler Belt Drive Engines
With - Camshaft Locking Pins
Flywheel Locking Pins
Balance Shaft Locking Pins
Tension Adjustment Wrench
Applicable to : Voyager | Grand Voyager
Jeep Cherokee / 01 - 08 | LDV Maxus / 05 - 08

Ford Timing Tool Set
for Ford 1.6 TI-VCT Duratec Engines
For timing belt replacement on 1.6 Ti-VCT Duratec EcoBoost Engines.
With Camshaft / Crankshaft and Flywheel Locking Pins
used to lock the camshafts in their timed position
when removing belts and pulleys during servicing.
Suitable for many other petrol and diesel Ford engines.

JLR Timing Tool Set
For Jaguar Land Rover 2.0 Chain Drive Petrol Engines
With crankshaft pulley and crankshaft sensor positioning tools

Ford Timing Tool Set
For locking and checking the camshaft on -
Ford / Jaguar 2.0L EcoBoost / Duratec Petrol Engines.
Land / Range Rover 2.0L GTDI and Si4 Diesel Engines.

Mercedes Timing Tool Set
Timing Chain Mounting Tool Set
for Mercedes-Benz M651 Diesel Engines
Allows precise positioning by preventing the timing chain skipping
and the camshaft sprockets moving when replacing the timing chain
without removing the camshaft sprockets.
Camshaft - Adjusting Tool and Special Wrench
Crankshaft Turning Tool
Sprocket Feet Shaft plus Screws
Timing Chain Guide Tool plus Screws

Mercedes Timing Chain Riveting Tool
For renewing and riveting timing chains on Mercedes-Benz Vehicles
Dismantling the timing chain case is often not required
as the new chain can be fed through using the existing chain.
Suitable for models with Duplex and Simplex timing chains with 4mm chain bolt.

Mercedes Timing Tool Set
Camshaft Alignment Tool Set
For Mercedes-Benz M271 Petrol Engines
Used for engine timing and belt changing.
Also other camshaft related servicing

Vauxhall / Opel Timing Tool Set
for 1.9 CDTI Diesel Engines
Timing and Locking Tool Kit for Camshafts and Crankshafts.
For Servicing and adjusting Timing belts -
includes Flywheel Holding Tool
Applicable to : 1.9 CDTI / TID / TTID & 2.0 CDTI / ECOFLEX

Renault Timing Tool Set
for 1.4 / 1.6 / 1.8 / 2.0 16V Belt Drive Engines
Suitable for timing belt replacement on
Renault and some Nissan and Vauxhall / Opel vehicles.
With Camshaft Rule and Locking Pins.
OEM Codes : MOT1489 | MOT1496 | MOT1054

VAG Timing Tool Set
for Porsche Cayenne and Panamera V8 Engines
Also Porsche Cayenne utilizing the M97/01 V8 engine.
For camshaft timing on Direct Fuel Injection /
Turbo and Normally-aspirated Engines
Allows TDC Timing during servicing the
Camshafts / Cylinder Head / Timing Chain
or Variable Valve-timing Cam Phasers.
Cayenne V8 up to 2007 and Cayenne and Panamera 2008 onwards

Volvo Timing Tool Set
for B4204 8 Speed Transmission Engines.
For aligning the camshaft and crankshaft and
working on valve drive and renewing the cylinder head gasket.
Belt Pulley Counter Holding Tool
Crankshaft Wheel Puller
Radial Seal Ring Mounting Tool
Camshaft Sprocket Tool
Camshaft Alignment Tool

Antifreeze and Coolant Tester
Easy read scale and pointers.
Calibrated in degrees C and F.
Tests ethylene glycol strength and includes temperature adjustment scale for accurate interpretation of mixture strength.
Tests Ethylene Glycol strength while the engine is hot or cold.
Composite body and rubber bulb for workshop durability.

Tube and Trim Cutter
With Multi-Angle Anvil and replaceable Utility Knife Blade.
Anvil Markings for 45 to 120 degree Angles.
Ideal for cutting Window Gaskets
Plastic Trim | Tubing and Conduit.

8L Pneumatic Auto Transmission Fluid Extractor and Refill Kit
with 13 Adaptor Set for Audi / Ford / Mercedes / VW.
Extract / transfer and dispense fluid quickly and cleanly
With Pre-set Safety valve for automatic shut-off.
Pressure gauge to read and control pressure.
2 way control valve for dispensing more safely.
13 one touch adaptors for automotive fluid transfer.
Screw valve to switch from extractor to dispenser.
High flow control valve to extract fluid more efficiently.

24 piece Engine Oil Filler Set with Rotation Handle
Allows for fast oil filling without spillage.
Great for many late model vehicles with internal baffles.
2 litre funnel fits adaptor for wide application range.
Colour coded plastic adaptors for oil filler access.
Special angle extension with swivel feature for hard to reach places.
Contains 19 specific adaptors for leakage-free connection.

16 litre Oil Drain Pan
Ideal for the Professional and Enthusiast Mechanic

12pc Oil Drain Plug Key Set
For use with 3/8in.Dr Ratchet
Hex keys : 8 | 9 | 10 | 12 | 14 | 17mm | 3/8in.
Square Keys : 8 | 11 | 13mm | 3/8in.
With 3/8in.Dr Sliding T-Bar.
Applicable to Oil Sumps on most modern vehicles

15oz / 445cc Grease Gun
Die Cast Pump Head with Air Bleed
Can be used with Cartridge or Bulk Grease
Supplied with Rigid and Flexible Tubes

Fast Fit Micro Puller 19 - 45mm
Supplied with thrust shaft extension
Capacity : 1 ton
Reach : 73mm
Puller Reach : 19 - 73mm / Min-Max
Puller Spread : 19- 45mm / Min-Max
Designed for the fast and safe removal of small bearings.
Also alternators / generators / domestic appliances / power tools and pumps.
Spring loaded and drop-forged legs are secured around the bearing or gear
by a screw collar to prevent slipping and subsequent damage or injury.

Adjustable Seal Puller
with 2 Hook Shapes
With rotating head for removing various oil and grease seals

Inner Tie Rod Installer / Remover Tool Set - 1/2in.Dr
Contains 12 SAE and Metric crowfoot adaptors
Sizes : 1-13/16 | 1-? | 1/5/16 | 1-3/8 | 1-7/16 | 1-1/2in.
29mm | 32.5mm | 33.6mm | 38.4mm | 40mm | 42mm
For inner tie rods that are inaccessible to adjust with a normal spanner.
The long socket slips over the tie rod end allowing the crowfoot adaptor
to engage with the fastener for easy removal and installation.
The inner tie rod can be removed and installed without removing the rack.

11pc Special Socket Set
for Castellated Lock Nuts
1/2in.Dr Sizes : 22 - 75mm
4 Tooth Sockets for removing castellated lock nuts
found on ball joints / axles and other applications.

Turnbuckle for Shock Absorber Top
Unique and comprehensive set of tools
for servicing spring or strut shock absorbers.
Suitable for a wide variety of vehicles
in conjunction with spring compressors.
Chrome Vanadium sockets and
Strut Nuts with 22mm hex drive.
Specialist bits with 10mm hex drive
Go-Thru Ratchet : 19 | 22mm.

Brake Fluid Tester
For accurately checking the quality of brake fluid.
With 5 LED?s to indicate percentage of water in the brake fluid.
Requires LR03 AAA 1.5V Battery / not included.
Automatic Power Off.

6pc Brake Bleed Wrench Set
Sizes : 7 | 8 | 9 | 10 | 11 | 12mm - 12 point
Combined Wrench / Socket and Nipple Connector.
Ideal for bleeding brake and hydraulic clutch systems without removing the wheels.
1.2M silicon hose with check valve for safety operating.
For universal bleeder nipples.

Pneumatic Brake Pressure Bleed Kit
Low pressure tank 10 - 40psi which can be pre-charged
with compressed air - making the unit fully portable.
Suitable for use on ABS systems.
Supplied with a range of vehicle adaptors.

Disc Brake Calliper Piston Rewind Set
Air Powered Wind Back Tool 80-100psi
Compatible with 3/8in.Dr tools
Right and Left hand Operation
Converter for 2 pin Adaptors
15 Wind Back Keys

Dial Test Indicator & Precision Point Set
0 - 10mm Dial in 0.01mm increments.
Magnetic base with fine adjustment.
Magnet has a 60kg pull.
On / Off Switch for easy positioning.
Used to check variations in machined parts.
Ideal for checking run-out on disc brakes.

Universal Press and Pull Sleeve Kit
Press Sleeves from 34 - 80mm Diameter in 2mm steps
Outside Diameter from 44 - 90mm in 2mm steps
5 x Pulling Spindles with nuts and thrust bearings
M10 | M12 | M14 M16 | M18

19pc Front Wheel Drive Bearing Service Kit
For the removal and installation of front hub bearings
without the need to dismantle the steering assembly.
Heavy Duty Steel Drifts : 55.5. to. 91mm

21pc Wheel Locking Nut Key Set
For removing Vauxhall / Opel locking wheel nuts on -
Agila | Astra F/G/H | Calibra | Corsa B/C/D |
Meriva | Omega B | Signum | Speedster |
Tigra A/B | Vectra B/C | Zafira A/B.
Vauxhall Wheel Lock Nut Keys equivalent to
OEM Z16512-181 to Z16512-200
With 17mm Alloy Wheel Nut Socket.

10pc Land Rover Wheel Locking Nut Key Set
Master Set of Tamper Proof Sockets
for removing the locking wheel nuts on Land Rover vehicles.
Hex Drive - Identified with : A | B | C | D | E | F | G | H | I | J.
Use with a 27mm Spanner or Socket
NOT for use with Impact Tools.

5pc Tesla Wheel Locking Nut Key Set
Applicable to Tesla Models : 3 / S / X
Identified as : A / B / C / D / E
For use with a 21mm Alloy Wheel Nut Socket or Spanner
Chrome Vanadium

4 Way Cross Wheel Brace
Sizes : 17 | 19 | 21 | 23mm
with Dipped Covered Shaft

21in. Extending Wheel Wrench
1/2in.Dr Socket : 17mm | 19mm
Extends from 340mm to 510mm
For use on vehicle Wheel Nuts

13pc Air Tool Kit / Ratchet Impact Gun and Sockets
1/2in.Dr Impact Wrench
3/8in.Dr Ratchet
Sockets : 9 | 10 | 11 | 13 | 14 | 17 | 19mm
3/8 to 1/2in. Adaptor
Mini Oiler Hex Key and Nipple

Soda Blasting Gun
Capacity : 1000ml
Operating Pressure : 6.3 - 8.2 bar
Air consumption : 57L/min
Air Inlet : 1/4in.bsp
Suitable for automotive use in removing
paint / mould / carbon / grease and rust.
Use with environmentally friendly soda blasting agents.
Particularly useful where less aggressive cleaning is required

5pc Spray Gun / Air Tool Kit
Includes High Pressure Spray Gun
Tyre Inflator with Gauge
Fluid Gun with Control Nozzle
Air Dust Gun
5M Recoil Air Hose 1/4in. BSP

7pc Spray Gun Kit
HVLP Spray Gun
Mini Spray Gun
Mini Regulator
150 and 600ml containers
Nozzles - 1.0 / 1.4mm
Pressure - 35 - 43psi
Air Inlet - 1/4in. BSP

2pc Tyre Lever Set
Both 12in. / 300mm

12in. / 300mm Tyre Lever

20in. / 500mm Tyre Lever

24in. / 600mm Tyre Lever

4pc Tesla Jack Pad Adaptor Set
Size : 75 x 50mm
Suitable for Tesla - 3 / Y / S / X model vehicles.
Simply insert the protection pad into the jack hole on the vehicle.
Avoids damaging the battery and the side skirt.

2 Ton Hydraulic Bottle Jack
Min. Height : 168mm
Max. Height : 316mm

20 Ton Hydraulic Bottle Jack
Min. Height : 235mm
Max. Height : 445mm

20 Ton Air Hydraulic Bottle Jack
Min. Height : 260mm
Max. Height : 510mm
Ram Travel : 170mm
Height Adjustment : 80mm
Air pressure : 20 - 180psi

12V Electric Winch
Rated Voltage : 12V DC
Motor : 1.7kw / 2.3hp
Capacity : 2000lbs / 907kg
Cable length : 15m
Cable diameter : 4mm
Reversible
Ideal for Horizontal Winching - Boats / Tree Stumps and Vehicles
Please be advised that the Winch Rollers shown on the box are NOT Included.

2000lb Electric Winch
Power Supply : 12V DC
Rolling Capacity : 6000lb
Pulling Capacity : 2000lb
Cable Length : 30ft / 9.1M
Maximum Boat Weight : 5000lb
Line Speed with load : 6ft /1.8M p/min
Weather resistant high-impact housing with folding handle.
Mounts securely to your trailer to provide pulling power
for boats / vehicles and other loading jobs.