5 Ton Hydraulic Gear Puller
6 Way 2 and 3 Leg Configuration
Up to 10 Ton Capacity

5 Ton Hydraulic Gear Puller
Maximum Capacity : 5T
Maximum Horizontal Pull Distance : 200mm
Maximum Vertical Pull Distance : 140mm
Axis Stroke : 50mm
Suitable for pulling hubs / flanges / gears and bearings.
Equipped with 3 reversible jaws suitable for different needs.

10 Ton Hydraulic Gear Puller
Maximum capacity : 10T
Maximum Horizontal Pull Distance : 250mm
Maximum Vertical Pull Distance : 160mm
Axis Stroke : 50mm
Suitable for pulling hubs / flanges / gears and bearings.
Equipped with 3 reversible jaws suitable for different needs.

Ford 5th Gear Puller
Fast and simple method of removing the fifth gear
on front wheel drive transmissions before carrying out internal repairs.
The split collar and retaining sleeve ensures a safe and positive location.
Applicable to : Fiesta / Focus / KA / Mondeo / C-Max / Galaxy and Transit Vans.

6pc VAG Axle Nut Socket Set
Includes 14mm and 17mm Hex Bits
M18 Spline Bit and 24 | 30 | 32mm 12-Point Sockets.
1/2in. and 3/4in. Drive
Covers most 1996-2015 VW / Audi Front and Rear Axle Nuts.

8pc Drive Shaft Socket Set
Socket and Bit Set Specific for Drive Shafts / Propshafts
1/2in.Dr Hex Bits : 14 | 17 | 19mm
1/2in.Dr Deep Sockets : 27 | 30 | 32 | 34 | 36mm
Chrome-Molybdenum Steel

CV Boot Hose Clamp Cutter
For removing hose clamps without damaging the CV boot.
The cutter head is angled at 45 degrees for improved access
Compact hardened steel cutting jaws
have a lift and cut action for accurate results.
Max jaw opening : 10mm
Jaw size : 0.5 x 0.7mm
Length : 215mm
Long reach with offset head for more leverage / cutting power.
Spring loaded handles for control & precision.

CV Joint Spring Ring Pliers
This tool is specifically designed to aid the secure removal
and re-installation of the CV Joint Spring Ring without damage.
With Unique jaws for holding the ring securely.
Length : 150mm
Jaw Capacity : 50mm

CV Boot Tool
For installing vehicle rubber CV boots without dismantling the CV joint.
Steel Centre / Plastic Composite Cone.
Diameter Size : 100mm Ex / 93mm Int.
Length : 405mm

Air Powered CV Boot Installation Tool
For the fast and efficient installation of uni-fit boots on the CV joint.
With air control switch to adjust fingers to the size of boot required.
Easily place the boot into place over CV joint.
The boot should be lubricated before each use.
Working pressure : 72-130psi
Air Inlet : 1/4in.

Air Powered Boot Installation Tool for CV Joints
Professional tool for commercial or occasional use.
Used for stretching flexible rubber CV boots
onto automatic drive shaft assemblies
Range : 20 - 110mm Diameter
Installs CV boots without removing axle.
Composite body with simple control valve.
For cars / small vans and light commercial vehicles.
1/4in. BSP inlet

Land Rover Prop Shaft Socket
9/16in. | 3/8in.Dr | 150mm Long
Suitable for
Defender : 90 | 110
Discovery : 1 | 2
Range Rover : P38

BMW Drive Shaft Tool
Suitable for 4 Wheel Drive Vehicles
For removing the drive shaft from the front axle.
Makes disassembly much easier.
OEM Code : 315110

2pc Lever Set
Ideal for clutch and transmission work - also
separating ball joint connections on shifter cables & shift linkages.
Plus axle components / ball joint connection points / exhaust hangers
silent blocks / bushes and many pan

C-Frame Socket Press Set for Drive Shaft Cardan Joints
Allows standard impact sockets to be used as press cups
for many Installation / Removal tasks on most vehicles.
Round Adaptors for : 1/4in | 3/8in | 1/2in | 3/4in Drive Sockets.
Anvil attachments for general bushing / bearing service tasks.
Durable Steel Frame Construction for up to 2.5 Tons.
3.5in. Throat Depth for wider Cardan Joints.
Forcing Screw : 6.5in.
Chrome-Molybdenum

7pc Drive Shaft Puller Set
230mm Long Puller with 120mm Housing
For BMW and VW Drive Shaft servicing

Adjustable Seal Puller
with 2 Hook Shapes
With rotating head for removing various oil and grease seals

5pc 1/2in.Dr Castellated Socket Set - Mercedes
Gearbox / differential flange / front axles and bearings / rear axle drive flange
6 / 8mm Tooth x 70 / 80mm Long
For Mercedes G Class -
W-107 / 114 / 115 / 116 / 123 / 126 / 460 / 461 / 463
Chrome Molybdenum

5pc 1/2in.Dr Castellated Socket Set - Mercedes
Gearbox / differential flange / front axles and bearings / rear axle drive flange
6 / 8mm Tooth x 70 / 80mm Long
For Mercedes G Class -
W-107 / 114 / 115 / 116 / 123 / 126 / 460 / 461 / 463
Chrome Molybdenum

BMW Differential Flange / Insert Nut Tool Set
For removing and installing of the drive shaft nut.
Allows inserting of the rear differential pinion seal.
Suitable for BMW vehicles with rear and four wheel drive.
HAG 215 Sp / HAG 220kom

MAN / TGA Front Axle Lock Nut Socket
3/4in.Dr / 60mm Hex Drive.
Inner diameter : 134mm
Outer diameter : 147mm
Lug diameter : 118mm / width 11mm
Applicable to Man / TGA Front Axle / V982l-01

Pitman Arm Puller
Opening Size : 33mm
Pull travel 63mm
Fits most cars and vans

19mm Puller for Land Rover Steering Drop Arms
For removing the steering drop arm from the steering box.
Over time the steering drop arm and box
can corrode together making it difficult to remove.
Using this tool will ensure the steering box spline shaft and oil seal will remain intact.

3pc VAG Steering Knuckle Pinch-Bolt Drift
for use when 9-10mm drift is required
on VAG vehicles with 4 link suspension.
Applicable to Audi A4 / A6 and Volkswagen Passat.
For use with a vibrating air hammer or air chisel.
The drift length is designed for ease of access
and the removal operation is in three stages.

7pc Universal Steering Knuckle Set
Enables the servicing of struts and ball joints
with aluminium or cast iron knuckles
and centralized and non-centralized slots.
13mm Hex Drive Knuckle Spreader
8 | 10 | 12mm Guide Pins
5 and 8mm deep Spreader Inserts
Hexagonal Key

5pc Tie Rod / Pitman Arm Adjustment Set
1/2in.Dr Suitable for cars / vans and trucks.
Sizes : 3/4 | 7/8 | 9/8 | 23/16 | 29/16in.
Allows 360 degree rotation of adjusting sleeve in tight areas.

Universal Tie Rod Wrench - 1/2in.Dr
Range from 27mm to 42mm
Easily removes inner tie rod ends without disassembling rack and pinion

Multi-Purpose Inner Tie Rod Tool
Compatible with 1/2in.Dr tool.
Use to replace the inner tie rod ends
without replacing the rack and pinion.
Capacity : 33 - 42mm

Electric Power Steering Rack Socket
for BMW and Mercedes-Benz Vehicles
3 Pin Rack Thrust Socket with 24mm Hex drive.
For the adjustment of the lateral rack and pinion clamping nut
Applicable to : BMW 1 / 3 / 4 series and X1 / X3 / X4

Rack Wrench - 1/2in.Dr
25 - 55mm Heavy Duty Steering Rack Tie Rod Wrench
Use to service all inner tie rod ends.
Prevents damage to rack components.
Use for removal or installation.
Clamp force increases as load is applied.
Suits multiple rack ends and sizes.

25 - 55mm Steering Rack Tie Rod Wrench - 1/2in.Dr
Heavy Duty use for removal or installation of inner tie rod ends.
Clamp force increases as load is applied.
Suits multiple rack ends and sizes.

Track Rod Wrench
Suitable for adjusting track rods as well as for general use.
Pipe wrench type design with quick fit spring loaded jaw.
Serrated jaws help prevent slippage and damage to track rods.
Overall length : 457mm / 18in.
Jaw Range : 10 - 35mm diameter

Inner Tie Rod Installer / Remover Tool Set - 1/2in.Dr
Contains 12 SAE and Metric crowfoot adaptors
Sizes : 1-13/16 | 1-? | 1/5/16 | 1-3/8 | 1-7/16 | 1-1/2in.
29mm | 32.5mm | 33.6mm | 38.4mm | 40mm | 42mm
For inner tie rods that are inaccessible to adjust with a normal spanner.
The long socket slips over the tie rod end allowing the crowfoot adaptor
to engage with the fastener for easy removal and installation.
The inner tie rod can be removed and installed without removing the rack.

Steering Arm Removal Tool - 28 / 35mm
Track Rod End Remover
27mm Hex or 1/2in Drive /400mm Long
Suitable for most European vehicles

Steering Arm Removal Tool - 35 / 45mm
Track Rod End Remover
27mm Hex or 1/2in Drive /400mm Long
Suitable for most European vehicles

Tie Rod Service Set
For tie rod servicing without additional alignment
Reduces the workload when changing tie rods.
For replacement of defective tie rod head.
Allows precise adjustment of new joint

7in. Ball Joint / Tie Rod Separator
Fork Type Separator
Jaw : 15mm

5pc Ball Joint and Tie Rod Separator Set
For separating most pitman arms / tie rods and ball joints
Found on a automotive and light truck vehicles.
With separators for late model Ford and GM pickups.
Sizes : 11/16in | 15/16in. | 1-1/8in. | 1-7/16in. | 1-5/8in.
Sizes : 19mm | 24mm | 30mm | 37mm | 42mm

5pc Ball Joint and Tie Rod Separator Set
Fork Type Track Rod Tool Kit
200mm Handle for use with a regular hammer
Handle with 0.401in. Shank for use with an air impact hammer

Size - 19 - 22mm

Universal Ball Joint Puller
For all types of vehicles
20mm Jaw opening adjustable up to 50mm

Ball Joint Separator
Scissor Type
Jaw Depth : 30 - 50mm
Jaw Opening : 19mm
For most makes and models of vehicles

Scissor Ball Joint Separator

Hydraulic Ball Joint Splitter
Forged steel body ball joint splitter suitable for light commercial vehicles.
Use manually or with 1.5 Tonne hydraulic ram supplied.
Features a step down thread adaptor that allows fitting of the manual force screw.
Jaw Opening : 22mm

2 Way Hydraulic Ball Joint Separator Kit
Specially designed to be operated manually or by 12 Tonne hydraulic ram.
Also for splitting Track Rod ends and Anti-roll Bar Mountings
Jaw Opening - 30 . 34 . 40 mm
Thrust Screw Lengths - 80 . 100mm
Pivot Rod Length - 125 mm.

Interchangeable Ball Joint Remover
A robust and adaptable service kit for most ball joints
Jaw Sizes : 20 | 22 | 24 | 27 | 30mm
Thrust Screw Length : 100mm
Pivot Rod Length - 125mm

Ball Joint Separator - Jaw size 15/16in.
Knurled shaft for better grip
Drop forged steel construction

3pc Ball Joint Removal Set
Low profile set suitable for most vehicles.
Features forged steel body and hardened screw with thrust ball.
23mm | 28mm | 34mm for various vehicles.

23mm Ball Joint Remover
for Cars, Light Trucks and SUVs
Opening on the support fork : 23mm
Opening on the puller housing : 62mm
Max. pressure range : 50mm
Hex Drive : 19mm
Suitable for impact wrenches.

30mm Ball Joint Remover
for Cars, Light Trucks and SUVs
Opening on the support fork : 30mm
Opening on the puller housing : 62mm
Max. pressure range : 50mm
Hex Drive : 19mm
Suitable for impact wrenches.