New Products
Diesel Engine Auxiliary Belt Tension Set

CT6385

Auxiliary Belt Tension Set

5pc Auxiliary Belt Tension Set
for Ford and PSA Diesel Engines.
Provides a safe and controlled method of adjusting the
tensioner position during removal and installation of the auxiliary belt.
Includes various adaptors along with an extension bar
to allow an extended reach on the raised peg which
can then be used with and appropriate tensioner wrench
and low profile thin walled socket.
Applicable to : 1.4 | 1.5 | 1.6 | 2.0 | 2.2 Diesel Engines.

Diesel Engine Auxiliary Belt Tension Set
t Click picture for more information
Ribbed Belt Tensioner Wrench

CT6358

Auxilliary Belt Tensioner Tool

Mercedes Auxilliary Belt Tensioner Tool
For tensioning and loosening the damper spring without damage.
on Mercedes-Benz W169 | W245 Engines
with air conditioning and / or stop-start function :
Suitable for following vehicles :
A-Class W169 / 2004 - 2012
A150 | A160 | A170 | A180 | A200 | A200T
B-Class W245 / 2005 - 2011
B150 | B160 | B170 | B180 | B200 | B200T
OEM Code : 266589003100

Ribbed Belt Tensioner Wrench
t Click picture for more information
Crankshaft Oil Seal Removal Kit - BMW

CT6411

Crankshaft Oil Seal Kit - BMW

BMW Crankshaft Seal Tool Set
For removing and installing the front and rear crankshaft seal.
Applicable to :
N20 / N26 / N40 / N42 / N45 / N45T
N46 / N46T / N52 / N53 / N54 / N55
OEM Codes : 119220 | 119230 | 119235

Crankshaft Oil Seal Removal Kit - BMW
t Click picture for more information
Oil Pump / Balance Shaft Alignment Kit

CT6286

Oil Pump / Balance Shaft Alignment Kit

Oil Pump / Balance Shaft Alignment Kit
for BMW 1 | 2 | 3 | 4 Series - 6L / 2.0L Petrol Engines.
For fixing the balance shaft and holding the chain sprocket
when used for repairing the chain and sprocket wheel drive.
Applicable to Engine Codes : N20 | N26 2012 - 2017
OEM Codes : 2 212 825 | 2 318 117 | 11 4 120

Oil Pump / Balance Shaft Alignment Kit
t Click picture for more information
Timing Tool Set - Mercedes / M282

CT6430

Timing Tool Set - Mercedes / M282

Timing Tool Set - Mercedes M282
For timing chain replacement and setting the timing on
Mercedes 1.3M 242.914 and Renault 1.3 LH5H -
chain driven twin camshaft 4 cylinder 1.3 Petrol Engines
OEM Code : 282589002300

Timing Tool Set - Mercedes / M282
t Click picture for more information
Camshaft Adjuster Quadrants

CT6429

Camshaft Adjuster - Mercedes

4pc Camshaft Adjuster Set
for Mercedes V6 / V8 - M152 / M157 / M276 / M278 Vehicles
Camshaft Position Sensor Reluctor Setting Tools
Used to mark pulse wheel on removed camshaft.
Can be used in conjunction with CT4076
OEM Code : 278589002300

Camshaft Adjuster Quadrants
t Click picture for more information
Timing Tool Set - Citroen / Peugeot

CT6362

Timing Tool Set - Vauxhall / Opel / Fiat

Diesel Engine Timing Tool Kit
for Citroen / Peugeot / Opel / Vauxhall
Fiat / Ford / Mazda / Renault / Volvo
With Flywheel Locking Pin
Injection Pump Locking Pins
Tensioner Retaining Tool

Timing Tool Set - Citroen / Peugeot
t Click picture for more information
Vauxhall / Opel Engine Timing Tool Set

CT6431

Timing Tool Set - Vauxhall / Opel

Vauxhall / Opel Timing Tool Set
For 1.6 SIDI | SIDI Turbo | SIDI Turbo EcoFLEX Engines
For checking and setting the engine timing when replacing the timing chain.
Camshaft Alignment Tool
Crankshaft Pulley Holding Tool
Balance Shaft Sprocket Locking Tools
Chain Tensioner Locking Pin

Vauxhall / Opel Engine Timing Tool Set
t Click picture for more information
Water Pump Sprocket Retainer

CT6449

Water Pump Sprocket Retainer

Water Pump Sprocket Holding Tool
for GM Ecotec engines.
Holds the timing chain and gear in place while
removing or installing water pump on
Chevrolet / Opel / Vauxhall Ecotec engines.
Simply remove access plate from front cover and install the tool.
OEM Code : EN-43651.

Water Pump Sprocket Retainer
t Click picture for more information
VAG Camshaft Drive Tensioner Wrench

CT6421

Camshaft Drive Tensioner Wrench - VAG

VAG Camshaft Drive Tensioner Wrench
For adjusting the Camshaft drive belt tensioner on
VAG Vehicles with 1.0 / 1.2 / 1.4 turbo charged engines.
Applicable to :
Audi - A1 / A3
Seat - Mii / Leon
Skoda - Octavia / Citigo
Volkswagen - Up / Golf V11
OEM Code : T10499

VAG Camshaft Drive Tensioner Wrench
t Click picture for more information
Manifold Suction Pipe Socket

CT6053

Manifold Fastener Socket

Special Socket
8 Point | 100mm Deep | 3|8in.Dr
For loosening and tightening intake manifold fastening screws.
Applicable to : Mercedes | Nissan | Opel | Renault Vehicles
with 1.6 DCi | CDTi Engines

Manifold Suction Pipe Socket
t Click picture for more information
R1234YF High Pressure Quick Coupler

CT6297

High Pressure Adjustable Quick Coupler - Red

High Pressure Adjustable Quick Coupler
Adapter for A/C manifold gauge set / R1234YF type.
Quick and easy connect / disconnect
Protection sleeve to provide safety protection
to avoid injury and refrigerant loss, defending against leakage.

R1234YF High Pressure Quick Coupler
t Click picture for more information
R1234YF Low Pressure Quick Coupler

CT6298

Low Pressure Adjustable Quick Coupler - Blue

Low Pressure Adjustable Quick Coupler
Adapter for A/C manifold gauge set / R1234YF type.
Quick and easy connect / disconnect
Protection sleeve to provide safety protection
to avoid injury and refrigerant loss, defending against leakage.

R1234YF Low Pressure Quick Coupler
t Click picture for more information
Air Conditioning System Test Kit

CT6296

Air Conditioning System Test Kit

Air Conditioning System Test Kit
For testing automotive air conditioning systems using R1234YF
refrigerant only by comparing the high and low pressure readings.
60mm gauges with tough rubber protective guard with 7/16in. copper coupler
Low : -30 - 120 psi / -1 - 8 bar
High : 0-500 psi / 0 - 35 bar
Blue Hose - 1/4in. FFL x 50in.
Red Hose - 1/4in. FFL x 50in.
Yellow Hose - 1/2in. ACME x 50in.
Sight glass for viewing condition of refrigerant.

Air Conditioning System Test Kit
t Click picture for more information
Pipe Line Stopper Kit

CT6360

Pipe Line Stopper Kit - 4pc

4pc Pipe Line Stopper Kit
Sizes : Banjo | 3/8 | 5/16 | 1/2 Inch
Spring loaded design for use with all Automotive Fluids.
Use to plug steel lines once disconnected.
Prevents fluid leaks and contamination during service.
Use with any automotive fluid.
Spring loaded design installs in seconds.

Pipe Line Stopper Kit
t Click picture for more information
Cone Type Pressure Test Kit

CT6404

Cooling System Pressure Test Kit

5pc Universal Cooling System Pressure Test Kit
Four universal cone adaptors fit a wide range of vehicles.
Hand pump with gauge allows simple and easy controlled testing.
Release pin allows depressurisation prior to detachment.
Contents:
Pressure pump
Cone adaptors : 17-24mm | 28-31.5mm | 37-39.5mm | 47-48.5mm
Cone adaptor system for sealing and pressurising the cooling system.

Cone Type Pressure Test Kit
t Click picture for more information
Tube and Trim Cutter Set

CT6146

Tube & Trim Cutter Set

Professional Multi-Angle Cutter Set
Multi-Angle Cutting Pliers with Wire Slot Cutters.
For Water Pipes / Line Pipes / Edge Banding Strip etc.
With Spare Blade and Small Open End Wrench.
Sturdy steel frame with plastic cover handle for comfortable diagonal cutting.
Multi-angle Anvil with : 45 | 60 | 75 | 90 | 105 | 120 Degree angles
For Pipes : 17 - 20 - 27mm

Tube and Trim Cutter Set
t Click picture for more information
9 litre Fluid Extractor

CT6405

Fluid Extractor - 9L

9L Manual Fluid Extractor
Suitable for extracting oil from vehicles and industrial machinery
also suitable for low-viscosity fluids such as water.
Automatic safety shut off mechanism when the tank is full.
Supplied with 3 tubes : 4mm / 6mm / 10mm Diameter.
Not for use with Toxic or Volatile Liquids.

9 litre Fluid Extractor
t Click picture for more information
Oil Sump Plug Key Set

CT6365

Oil Sump Plug Key Set - 9pc

9pc Oil Sump Plug Keys
Special Profile Set for assembly and disassembly of
plastic oil drain screws on plastic oil sumps.
Supplied with 3/8in.Dr T-handle or use with 17mm Socket.
For manual operation - do not use power tools.
Applicable to : Ford / PSA / BMW / VAG / Mercedes / DAF / MAN / GM.

Oil Sump Plug Key Set
t Click picture for more information
Pipe Plug Socket Set

CT6058

Pipe Plug Socket Set - 11pc

11pc 3/8in.Dr Pipe Plug Socket Set
Male : 3/16 | 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Female : 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Tapered Male Square Drive and
Chamfered Female Square Drive aligns socket to fastener quickly
Low profile design provides easy access to tight spaces
Fits any 3/8in.Dr ratchets, bars etc.
Chrome-Molybdenum for high torque impact tools.

Pipe Plug Socket Set
t Click picture for more information
Ford Oil Drain Plastic Plugs

CT6232

Oil Sump Plug Set - 5pc / Ford

5pc Ford Plastic Oil Drain Plug Set
Replacement Nylon Oil Drain Plugs for Ford vehicles.
Heavy Duty Plastic Plug.
OEM Code : 1830727

Ford Oil Drain Plastic Plugs
t Click picture for more information
Mercedes Replacement Oil Drain Plugs

CT6234

Oil Sump Plug Set - 5pc Mercedes

5pc Oil Drain Plastic Plug Set
Replacement Nylon Oil Drain Plugs for Mercedes Benz vehicles.
Complete with sealing ring.
OEM Code : A0029902017

Mercedes Replacement Oil Drain Plugs
t Click picture for more information
VAG Oil Drain Plastic Plug Set

CT6233

Oil Sump Plug Set - 5pc VAG

5pc Oil Drain Plastic Plug Set
Replacement Nylon Oil Drain Plugs for VAG vehicles.
Also suits CAM cover on 1.6 / 2.0 TDI diesel engines.
OEM Code : 06L 103 801.

VAG Oil Drain Plastic Plug Set
t Click picture for more information
Filter Housing Wrench

CT6269

Oil Filter Housing Wrench - 74.5mm

74.5mm Oil Filter Wrench - 15pt / 3/8in.Dr
For Ford 1.5 | 1.6 EcoBoost Engines
Allows the correct removal and fitment of the fuel filter housing
matching the fuel canister designed filter.
With offset design ideal for use in confined areas.
Applicable to : C-Max II | Focus III | Galaxy III
Kuga II | Mondeo IV / V | S-Max II | Transit Connect II.

Filter Housing Wrench
t Click picture for more information
Dual Clutch Oil Seal Fitting Kit

CT6368

Dual Clutch Oil Seal Fitting Kit

DCT Wet Clutch Oil Seal Fitting Kit
For Ford and Volvo vehicles fitted with the Dual Wet Clutch System
also vehicles with Getrag MPS6 / 6DCT 450 gearboxes.
Includes the seal guide and cover press used for
the fitting of the clutch cover without damaging the centre seal.
OEM Codes : 308-764 | 308-783 | 9997383 | 9997388.

Dual Clutch Oil Seal Fitting Kit
t Click picture for more information
DSG Clutch Installation Kit - Ford

CT6361

DSG Clutch Installation Kit - Ford

DSG Dual Clutch Transmission Tool Kit
Ford Focus DCT Dual Clutch Transmission DPS6
Specially designed to disassemble and install dry transmissions
It re-springs / re-trips the springs on the clutch so that you can reinstall it again.
Fiesta 2011 - 2019
Focus 2012 - 2018
Transit Connect 2019
B-MAX since 2012
OEM Code : 307675

DSG Clutch Installation Kit - Ford
t Click picture for more information
CV Joint Boot Clamp Pliers

CT6425

CV Joint Boot Clamp Pliers

Offset CV Joint Boot Clamp Pliers
Special Boot Clamp Crimping Pliers designed to work in confined spaces
allows you to work on large size boot clamps / top plate on pliers flatten the crimp.
The pliers work from the side - head is turned 90 degrees
unlike traditional tools that work from the end.
Use on eared clamps and Perma-Quick type clamps
used on fuel filters / cooling systems and vacuum lines.
Length : 245mm
Max. Clamping Width : 31mm

CV Joint Boot Clamp Pliers
t Click picture for more information
Inner Drive Shaft Extractor Fork

CT6382

Inner Drive Shaft Extractor Fork

Inner Drive Shaft Extractor Fork
for Ford / Volvo / Renault / Mazda etc.
Contact Lever Diameter : 55mm.
Jaw Diameter : 85mm.
Length : 380mm.
Designed to allow for the quick and safe removal of drive shafts
by connecting properly with the locking clip rings found on many
front wheel drive vehicles preventing damage to the
drive shaft and surrounding components.

Inner Drive Shaft Extractor Fork
t Click picture for more information
Differential Flange / Insert Nut Tool Set

CT6410

Differential Flange / Insert Nut Tool Set

BMW Differential Flange / Insert Nut Tool Set
For removing and installing of the drive shaft nut.
Allows inserting of the rear differential pinion seal.
Suitable for BMW vehicles with rear and four wheel drive.
HAG 215 Sp / HAG 220kom / HAG 225kom / HAG type G
Open End Spanner - 50mm
Flange Holding Tool
Multi-Point Ring Spanner - 65mm
Multi-Point Socket - 34T
Seal Ring Drift

Differential Flange / Insert Nut Tool Set
t Click picture for more information
Motorcycle Suspension Nut Socket

CT6393

Suspension Nut Socket - Suzuki

Suzuki Suspension Castle Nut Socket
4 Pin / 1/2in.Dr Socket
External 43mm / Internal 30.5mm
Pins : 5mm x 6.3mm
Applicable to : V650 / 1000 | DI650 / 1000 | V-Storm
Also Hayabusa / Bking and GSX-R750 / 1000 / 1100

Motorcycle Suspension Nut Socket
t Click picture for more information
Suspension Strut Nut Socket - VAG

CT6379

Suspension Nut Wrench - VAG

13mm Suspension Top Mount Nut Wrench
for VAG - Audi | Seat | Skoda | VW
13mm 6 / 8 point Dual Sided Swivel Socket
120mm Total Length with 3/8in.drive.
Specialist tool designed to be used when
removing the top of Macpherson strut mounts.
Flexible for hard to reach parts allowing access
to the strut mount with minimal effort due to the flexible design.

Suspension Strut Nut Socket - VAG
t Click picture for more information
Electric Brake Fluid Bleed System

CT6228

Brake Fluid Bleed System - Electric

Electric Brake Fluid Bleeder
For most makes and models of vehicles
With Adjustable pulse oil change which can effectively
clean the pipeline and change the oil more thoroughly.
Contents : Brake Fluid Bleeder / 2L Bottle & 3.5M Hose / 3 Adaptors.
Power supply : 240V | 50 / 60Hz | 35W
Output Pressure : 0.6 - 3.0 Bar
Output flow : <= 1.2L / Min
Noise Level : 70 Db
Device shuts off when container is empty

Electric Brake Fluid Bleed System
t Click picture for more information
Ball End Bearing Puller Kit

CT6293

Bearing Puller Set

Bearing Puller Kit with Ball Ended Puller Adaptor
Suitable for removal of a variety of blind bearings
where traditional bearing and gear pullers will not reach.
Ball-end tips fit inside bearing races to provide traction for bearing extraction.
Bearing Sizes : 5 / 6 / 8 / 9 / 11 / 12.5mm

Ball End Bearing Puller Kit
t Click picture for more information
Universal Wheel Bearing Spreader

CT6402

Wheel Bearing Spreader

Universal Wheel Bearing Spreader
Designed to separate the suspension strut from the wheel bearing housing.
Spreading range : 5.0 - 11.5mm
Drive : 17mm Hex

Universal Wheel Bearing Spreader
t Click picture for more information
Wheel Bearing Ring Puller - 68mm

CT6357

Wheel Bearing Ring Puller - 68mm

68mm Bearing Inner Ring Puller
For removing the inner wheel bearing rings on wheel hubs.
The bearing rings usually remain on the wheel hub
when the wheel bearings are removed.
Integral Clamp holds the puller legs
securely behind the component to be removed.
Pressure piece diameter : 25 x 30mm
Puller width : 68mm
Puller depth : 60 mm

Wheel Bearing Ring Puller - 68mm
t Click picture for more information
Bearing Service Kit

CT6292

Bearing Separator Set

Bearing Separator
Drop forged
Clamping Width : 46mm - 230mm max
Clamping Bolt Length : 350mm / Distance : 224mm / Thread : M25 x 2.5
Puller Bolt : 3/4in. x 10 UNC
Puller Bolt distance : 164mm / 350mm max
Splitting Knife Base : 102mm - 288mm max
Suitable for removing bearings / gears and bushings from shafts.

Bearing Service Kit
t Click picture for more information
Tyre Lever Set : 12 inch

CT2661

Tyre Lever Set - 2pc

2pc Tyre Lever Set
Both 12in. / 300mm
Chrome Vanadium
Supplied in a Pouch

Tyre Lever Set : 12 inch
t Click picture for more information
Tyre Bead Retainer

CT6267

Tyre Bead Retainer

Tyre Bead Retainer
With High Density Rubberized PVC Coating -
prevents the tyre bead from creeping when mounting the top head.
Solid metal core construction is extremely durable.
Easily clips into place with one hand - use with tyre spoons or tyre lever.
Suitable for all tyres.
Ideal for use with CT6266.

Tyre Bead Retainer
t Click picture for more information
Tyre Bead Retainer

CT6268

Tyre Bead Retainer

Tyre Bead Retainer
Constructed from Wear-proof Reinforced Nylon
designed to better protect your tyre rim and tool.
Can be used on aluminium and steel wheels.
Ideal for use with CT6266.

Tyre Bead Retainer
t Click picture for more information
Polyesyer Webbing Sling - 2M / 2Ton

CT0489

Webbing Sling - 2M / 2Ton

2M / 2Ton Flat Webbing Sling
60mm Wide
Safety Factor : 7:1
Made from Polyester

Polyesyer Webbing Sling - 2M / 2Ton
t Click picture for more information
Polyesyer Webbing Sling - 2M / 3Ton

CT0493

Webbing Sling - 2M / 3Ton

2M / 3Ton Flat Webbing Sling
90mm Wide
Safety Factor : 7:1
Made from Polyester

Polyesyer Webbing Sling - 2M / 3Ton
t Click picture for more information
Polyesyer Webbing Sling - 5M / 2Ton

CT0490

Webbing Sling - 5M / 2Ton

5M / 2Ton Flat Webbing Sling
60mm Wide
Safety Factor : 7:1
Made from Polyester

Polyesyer Webbing Sling - 5M / 2Ton
t Click picture for more information
Polyesyer Webbing Sling - 5M / 3Ton

CT0494

Webbing Sling - 5M / 3Ton

5M / 3Ton Flat Webbing Sling
90mm Wide
Safety Factor : 7:1
Made from Polyester

Polyesyer Webbing Sling - 5M / 3Ton
t Click picture for more information
Half Coupler with Lifting Eye

CT6145

Lifting Bolt with Half Coupler

Half Coupler with Lifting Eye
Width : 50mm
Tube Diameter : 38 - 52mm
Hoist Weight : 340kg
Fixings : M12 Eye Nut

Half Coupler with Lifting Eye
t Click picture for more information
Tow Bar Scale

CT6427

Tow Bar Scale

100kg Aluminium Tow Bar Scale
Weight Scale : 50 - 100kg
Total Length : 430mm
Tube Diameter : 37mm
For caravans / mobile homes and trailers
Simply place under the drawbar and read the value.

Tow Bar Scale
t Click picture for more information
EV / Hybrid Vehicle Warning Sign

CT6160

EV / Hybrid Vehicle Warning Sign

EV / Hybrid Warning Sign
3 Sided with Magnetic Base
Made of hard-wearing plastic.
Weather & scratch resistant.
With water drain hole in the bottom.
Magnet moulded in to plastic sign to prevent scratches.
Designed to serve as a warning that a vehicle is EV or Hybrid

EV / Hybrid Vehicle Warning Sign
t Click picture for more information
EV / Hybrid Vehicle Warning Sign

CT6161

EV / Hybrid Vehicle Warning Sign

EV / Hybrid Warning Sign
3 Sided with Magnetic Base
Made of hard-wearing plastic.
Weather & Scratch resistant.
With water drain hole in the bottom.
With suction cup - suitable for indoor and outdoor use.
Designed to serve as a warning that a vehicle is EV or Hybrid

EV / Hybrid Vehicle Warning Sign
t Click picture for more information
Mechanics EVA Work Mat

CT5948

Mechanics Work Mat

Heavy Duty EVA Foam Work Mat
100 x 45cm Dual Layer
Hard Wearing
Water and Oil Resistant
Ideal for the professional and enthusiast mechanic.

Mechanics EVA Work Mat
t Click picture for more information
Magnetic Vehicle Wing Cover

CT6435

Mechanics Vehicle Wing Cover

Mechanics Vehicle Wing Cover
With 4 pockets for holding tools while working on car.
Wing cover held in place by integral magnets.
PVC material prevents scratching and marking of paintwork.
Protects vehicle body from damage while being serviced or repaired.
Size : 1200 x 1000mm

Magnetic Vehicle Wing Cover
t Click picture for more information
Utility Tool Cart with 3 Shelves

CT0681

Tool Trolley - 3 Shelves

Folding Garage / Workshop Trolley
Easy access for adding or removing items to and from trolley.
4 Large Castor Wheels with 2 locking.
Overall Size : 640mm W x 375mm D x 830mm H
Shelf Size : 595mm W x 370mm D x 35mm H
Capacity : 30kg per shelf
Folds up in seconds for easy storage when not in use.
Can also be used as a janitorial trolley.

Utility Tool Cart with 3 Shelves
t Click picture for more information

Product Search

Search Icon
Section 1 Icon Section 2 Icon Section 3 Icon Section 4 Icon Section 5 Icon Section 6 Icon Section 7 Icon Section 8 Icon Section 9 Icon Section 10 Icon

Cannon Tools Limited   •  20 Station Road,  Rowley Regis,  West Midlands,  B65 0JU,  United Kingdom

 T +44 (0) 121 561 6760