27mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

29mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

30mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

32mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

33mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

34mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

35mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

36mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

38mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

39mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

41mm - Deep Impact Socket
1/2in.Dr
Axle / Spindle Nut Socket
for Front wheel drive vehicles

1/2in.Dr Socket Set for Axle Nuts
Sizes - 29 | 30 | 31 | 32 | 33 | 34 | 35 | 36 | 38mm

Tie Rod Puller for use on Front wheel drive vehicles with rack and pinion steering

Pitman Arm Puller
Opening Size : 33mm
Pull travel 63mm
Fits most cars and vans

19mm Puller for Land Rover Steering Drop Arms
For removing the steering drop arm from the steering box.
Over time the steering drop arm and box
can corrode together making it difficult to remove.
Using this tool will ensure the steering box spline shaft and oil seal will remain intact.

24mm Puller for Land Rover Steering Drop Arms
For removing the steering drop arm from the steering box.
Over time the steering drop arm and box
can corrode together making it difficult to remove.
Using this tool will ensure the steering box spline shaft and oil seal will remain intact.

3pc VAG Steering Knuckle Pinch-Bolt Drift
for use when 9-10mm drift is required
on VAG vehicles with 4 link suspension.
Applicable to Audi A4 / A6 and Volkswagen Passat.
For use with a vibrating air hammer or air chisel.
The drift length is designed for ease of access
and the removal operation is in three stages.

7pc Universal Steering Knuckle Set
Enables the servicing of struts and ball joints
with aluminium or cast iron knuckles
and centralized and non-centralized slots.
13mm Hex Drive Knuckle Spreader
8 | 10 | 12mm Guide Pins
5 and 8mm deep Spreader Inserts
Hexagonal Key

5pc Tie Rod / Pitman Arm Adjustment Set
1/2in.Dr Suitable for cars / vans and trucks.
Sizes : 3/4 | 7/8 | 9/8 | 23/16 | 29/16in.
Allows 360 degree rotation of adjusting sleeve in tight areas.

Universal Tie Rod Wrench - 1/2in.Dr
Range from 27mm to 42mm
Easily removes inner tie rod ends without disassembling rack and pinion

Multi-Purpose Inner Tie Rod Tool
Compatible with 1/2in.Dr tool.
Use to replace the inner tie rod ends
without replacing the rack and pinion.
Capacity : 33 - 42mm

Electric Power Steering Rack Socket
for BMW and Mercedes-Benz Vehicles
3 Pin Rack Thrust Socket with 24mm Hex drive.
For the adjustment of the lateral rack and pinion clamping nut
Applicable to : BMW 1 / 3 / 4 series and X1 / X3 / X4.
Also Mercedes-Benz C and S-class

Rack Wrench - 1/2in.Dr
25 - 55mm Heavy Duty Steering Rack Tie Rod Wrench
Use to service all inner tie rod ends.
Prevents damage to rack components.
Use for removal or installation.
Clamp force increases as load is applied.
Suits multiple rack ends and sizes.

25 - 55mm Steering Rack Tie Rod Wrench - 1/2in.Dr
Heavy Duty use for removal or installation of inner tie rod ends.
Clamp force increases as load is applied.
Suits multiple rack ends and sizes.

Track Rod Wrench
Suitable for adjusting track rods as well as for general use.
Pipe wrench type design with quick fit spring loaded jaw.
Serrated jaws help prevent slippage and damage to track rods.
Overall length : 457mm / 18in.
Jaw Range : 10 - 35mm diameter

Inner Tie Rod Installer / Remover Tool Set - 1/2in.Dr
Contains 12 SAE and Metric crowfoot adaptors
Sizes : 1-13/16 | 1-? | 1/5/16 | 1-3/8 | 1-7/16 | 1-1/2in.
29mm | 32.5mm | 33.6mm | 38.4mm | 40mm | 42mm
For inner tie rods that are inaccessible to adjust with a normal spanner.
The long socket slips over the tie rod end allowing the crowfoot adaptor
to engage with the fastener for easy removal and installation.
The inner tie rod can be removed and installed without removing the rack.

4pc Track Rod Set
For the removal and replacement of the inner steering ball joint
without the need to dismantle the steering rack from the bulkhead.
Drive Head Range -
30 - 35mm diameter
35 - 40mm diameter
40 - 45mm diameter

Steering Arm Removal Tool - 28 / 35mm
Track Rod End Remover
27mm Hex or 1/2in Drive /400mm Long
Suitable for most European vehicles

Steering Arm Removal Tool - 35 / 45mm
Track Rod End Remover
27mm Hex or 1/2in Drive /400mm Long
Suitable for most European vehicles

Tie Rod Service Set
For tie rod servicing without additional alignment
Reduces the workload when changing tie rods.
For replacement of defective tie rod head.
Allows precise adjustment of new joint

7in. Ball Joint / Tie Rod Separator
Fork Type Separator
Jaw : 15mm

5pc Ball Joint and Tie Rod Separator Set
Automotive front-end service set for removal of most types of Pitman Arms

5pc Ball Joint and Tie Rod Separator Set
For separating most pitman arms / tie rods and ball joints
Found on a automotive and light truck vehicles.
With separators for late model Ford and GM pickups.
Sizes : 11/16in | 15/16in. | 1-1/8in. | 1-7/16in. | 1-5/8in.
Sizes : 19mm | 24mm | 30mm | 37mm | 42mm

5pc Ball Joint and Tie Rod Separator Set
Fork Type Track Rod Tool Kit
200mm Handle for use with a regular hammer
Handle with 0.401in. Shank for use with an air impact hammer

Universal Wheel Axle Nut Remove and Installation Kit
Engineered to loosen and tighten the rear wheel nut.
Both sides of pin are adjustable.
3 sets of pins for different vehicles.
For vehicles over 2 tons with circular nuts.
Pins : 5.5 | 6.8 | 9.1mm / Nut : M8 x P1.25

Universal Outside Thread Chaser 5 - 130mm Diameter
For use on axle tubes / thrust rods / steering rods etc.
Quickly restores threads without the need for cutting.
Can be attached to any undamaged thread position
and re-grooves the thread from this position.
Re-grooving inserts / right and left hand threads :
Metric thread pitches : 1.0 - 3.5mm
Imperial thread pitches : 4 - 24