Extra-Long Spline Socket Bit
M10 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

Extra-Long Spline Socket Bit
M12 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

Extra-Long Spline Socket Bit
M14 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

11pc 3/8in.Dr Pipe Plug Socket Set
Male : 3/16 | 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Female : 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Tapered Male Square Drive and
Chamfered Female Square Drive aligns socket to fastener quickly
Low profile design provides easy access to tight spaces
Fits any 3/8in.Dr ratchets, bars etc.
Chrome-Molybdenum for high torque impact tools.

6pc VAG Axle Nut Socket Set
Includes 14mm and 17mm Hex Bits
M18 Spline Bit and 24 | 30 | 32mm 12-Point Sockets.
1/2in. and 3/4in. Drive
Covers most 1996-2015 VW / Audi Front and Rear Axle Nuts.

8pc Drive Shaft Socket Set
Socket and Bit Set Specific for Drive Shafts / Propshafts
1/2in.Dr Hex Bits : 14 | 17 | 19mm
1/2in.Dr Deep Sockets : 27 | 30 | 32 | 34 | 36mm
Chrome-Molybdenum Steel

CV Boot Clamp Pliers - 2pc Set
Crimps and flattens ear type Clamps
CV Clamp Banding Tool
For installing CV Clamps
Standard banding tool for CV Joint Boots

CV Joint Boot Clamp Pliers - Ear Type
Ideal for installing Clamps on fuel filters - water pumps - CV joint boots and other cooling system hoses

CV Drive Shaft Boot Clamp Pliers
For Oetiker CV Drive Shaft boot Securing clips.
3/8in.Dr holes in the handle shafts to enable
a torque Wrench to be used with the tool when required.

Offset CV Joint Boot Clamp Pliers
Special Boot Clamp Crimping Pliers designed to work in confined spaces
allows you to work on large size boot clamps / top plate on pliers flatten the crimp.
The pliers work from the side - head is turned 90 degrees
unlike traditional tools that work from the end.
Use on eared clamps and Perma-Quick type clamps
used on fuel filters / cooling systems and vacuum lines.
Length : 245mm
Max. Clamping Width : 31mm

CV Joint Boot Clamp Tool
For the assembly of Stainless Steel Bands
3/8in.Dr Jaws for use with a Torque Wrench
For torque sensitive rubber boot Clamps

CV Joint Spring Ring Pliers
This tool is specifically designed to aid the secure removal
and re-installation of the CV Joint Spring Ring without damage.
With Unique jaws for holding the ring securely.
Length : 150mm
Jaw Capacity : 50mm

CV Boot Tool
For installing vehicle rubber CV boots without dismantling the CV joint.
Steel Centre / Plastic Composite Cone.
Diameter Size : 100mm Ex / 93mm Int.
Length : 405mm

Air Powered CV Boot Installation Tool
For the fast and efficient installation of uni-fit boots on the CV joint.
With air control switch to adjust fingers to the size of boot required.
Easily place the boot into place over CV joint.
The boot should be lubricated before each use.
Working pressure : 72-130psi
Air Inlet : 1/4in.

Air Powered Boot Installation Tool for CV Joints
Professional tool for commercial or occasional use.
Used for stretching flexible rubber CV boots
onto automatic drive shaft assemblies
Range : 20 - 110mm Diameter
Installs CV boots without removing axle.
Composite body with simple control valve.
For cars / small vans and light commercial vehicles.
1/4in. BSP inlet

Land Rover Prop Shaft Socket
9/16in. | 3/8in.Dr | 150mm Long
Suitable for
Defender : 90 | 110
Discovery : 1 | 2
Range Rover : P38

BMW Drive Shaft Tool
Suitable for 4 Wheel Drive Vehicles
For removing the drive shaft from the front axle.
Makes disassembly much easier.
OEM Code : 315110

Inner Drive Shaft Extractor Fork
Designed to engage between the inner drive shaft
and the gearbox housing to lever out the drive shaft.
Total length : 400mm
Jaw width : 82mm
Required on Ford / Mazda / Volvo / Renault / Dacia
and other front wheel drive vehicles.

Inner Drive Shaft Extractor Fork
for Ford / Volvo / Renault / Mazda etc.
Contact Lever Diameter : 55mm.
Jaw Diameter : 85mm.
Length : 380mm.
Designed to allow for the quick and safe removal of drive shafts
by connecting properly with the locking clip rings found on many
front wheel drive vehicles preventing damage to the
drive shaft and surrounding components.

2pc Lever Set
Ideal for clutch and transmission work - also
separating ball joint connections on shifter cables & shift linkages.
Plus axle components / ball joint connection points / exhaust hangers
silent blocks / bushes and many panel types and stuck components
Large Lever / Internal dimensions : 25 x 110mm.
Small Lever / Internal dimensions : 15 x 65mm

Inner CV Joint Puller
Includes Slide Hammer and 48mm CV Joint Fork.
For removing the axle assembly from the transaxle without
causing damage to aluminium transmission cases or roller bearings.
For most Ford vehicles and other car manufactures.

7pc Drive Shaft Puller Set
230mm Long Puller with 120mm Housing
For BMW and VW Drive Shaft servicing

Adjustable Propshaft Separator
Will fit most makes and models of vehicles - except Seat.

Adjustable Seal Puller
with 2 Hook Shapes
With rotating head for removing various oil and grease seals

3pc Seal Puller Set
Suitable for the safe damage free removal of Drive or Transmission Oil and Grease seals or O-rings.
Tool head shape provides better access than other seal pullers.

5pc 1/2in.Dr Castellated Socket Set - Mercedes
Gearbox / differential flange / front axles and bearings / rear axle drive flange
6 / 8mm Tooth x 70 / 80mm Long
For Mercedes G Class -
W-107 / 114 / 115 / 116 / 123 / 126 / 460 / 461 / 463
Chrome Molybdenum

5pc 1/2in.Dr Castellated Socket Set - Mercedes
Gearbox / differential flange / front axles and bearings / rear axle drive flange
6 / 8mm Tooth x 70 / 80mm Long
For Mercedes G Class -
W-107 / 114 / 115 / 116 / 123 / 126 / 460 / 461 / 463
Chrome Molybdenum

72mm Differential Nut Socket
For loosening or tightening the castellated differential nut
used on the Mercedes-Benz Citaro and Evo Buses.
Castellated 6 Tooth Socket : 11 x 6 x 12mm deep Teeth
Outside Diameter : 84mm | Inside Diameter : 72mm.
Depth : 60mm with 32mm Hex drive.

Mercedes Rear Axle Groove Nut Socket
For 6 teeth groove nuts on low-floor buses with SF portal axle AV132 -
Mercedes-Benz Citaro Bus / MAN City-Line / Neoplan / Kassbohrer
and other vehicles with identical axle.
Designed for high tightening and release torque values.
by hand or impact wrench operation.
Drive tube diameter : 35 mm

MAN / TGA Front Axle Lock Nut Socket
3/4in.Dr / 60mm Hex Drive.
Inner diameter : 134mm
Outer diameter : 147mm
Lug diameter : 118mm / width 11mm
Applicable to Man / TGA Front Axle / V982l-01

BMW Differential Flange / Insert Nut Tool Set
For removing and installing of the drive shaft nut.
Allows inserting of the rear differential pinion seal.
Suitable for BMW vehicles with rear and four wheel drive.
HAG 215 Sp / HAG 220kom / HAG 225kom / HAG type G
Open End Spanner - 50mm
Flange Holding Tool
Multi-Point Ring Spanner - 65mm
Multi-Point Socket - 34T
Seal Ring Drift

4pc Spoon Tip Seal Remover Set
with rounded tip and blended edge
for the removal of seals and O-rings
without damage to seal or surface.
2 x Spoon Tips
2 x Contoured Tips
For Seals / Dust Boots / O-rings / Hoses.