21pc Universal Motorcycle Chain Tool Kit
For Timing Chains and Drive Chains.
Includes a pair of chain link clip removal pliers
for removal and installation of chain lock clips.
A chain stretch tool that holds both ends of the chain tog

9pc Motorcycle Fork Seal Driver Set
For use on conventional and upside-down forks.
Sizes : 35/36 | 39 | 41 | 43 | 45 | 46/47 | 48 | 49/50 | 54 mm.
Allows quick and convenient replacement of fork seals.
without disassembling the fork legs.
Zinc plated with knurled ring for better grip

Motorcycle Brake Caliper Piston Remover
Range : 18mm - 30mm
Universal

Motorcycle Brake Piston Removal Tool Set
For dismantling motorcycle brakes with sliding Calipers.
Removes frozen Pistons with ease.
Includes 12 universal adaptors - 19 to 30mm.
Will not mark or damage the working part of the Piston.
Suitable for nearly all makes and models

Rear Wheel Axle Nut Socket
Dual size : 41mm / 46mm for Ducati motocycles
46mm socket for the rear wheel nut and
41mm socket for the sprocket retainer nut.
Can be used with standard ratchets or impact guns.
Applicable to : Ducati 7

Wheel Nut Socket for Ducati Motorcycles
Dual Size : 55mm 12 Point & 30mm Hex.
This low profile socket is designed to remove both front and
rear wheel nuts that have been over tightened or are partially seized.
Applicable to Ducati Supe

60mm Wheel Nut Socket for KTM Rear
1/2in.Dr / 60mm Single Hex Shallow Socket
with central boss which keeps the socket engaged
and aligned when removing high torque fixings.
Can be used with standard ratchets or impact guns.
Appli

BPW Rear Hub Cap Nut Socket
Size : 95mm / Oval | 41mm Deep | 3/4in.Dr
Rear axle cover extractor socket.
Applicable to : BPW / 6.5 - 9 ton

BPW Rear Hub Cap Nut Socket
Size : 109mm / Oval | 41mm Deep | 3/4in.Dr
Rear axle cover extractor socket.
Suitable for later model of Japanese commercial trucks
tractors and other automotive industrial equipment.

BPW Rear Hub Cap Nut Socket
Size : 110mm / Oval | 41mm Deep | 3/4in.Dr
The rear axle cover extractor socket.
Applicable to : BPW / 12 ton

BPW Rear Hub Cap Nut Socket
Size : 120mm / Oval | 41mm Deep | 3/4in.Dr
Rear axle cover extractor socket.
Applicable to : BPW 13-14 ton trailer from November 2004

BPW Axle Nut Socket
80mm | 3/4in.Dr
Wrench Size : 80 x 50mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Nut Socket
85mm | 3/4in.Dr
Wrench Size : 85 x 50mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Nut Socket
95mm | 3/4in.Dr
Wrench Size : 95 x 40mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Nut Socket
110mm | 3/4in.Dr
Wrench Size : 110 x 45mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Nut Socket
120mm | 3/4in.Dr
Wrench Size : 120 x 48.5mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Extractor - M125 x 2.0
For removing the wheel axle with outer thread on commercial vehicles.
Extremely robust European truck repair tool applicable to :
BPW 12 ton models.
Used in combination with 30mm and 43mm spanners
H

BPW Axle Extractor - M135 x 2.0
For removing the wheel axle with outer thread on commercial vehicles.
Extremely robust European truck repair tool applicable to :
BPW ECO 10 - 12 ton old models.
Used in combination with 30mm and 43mm sp

BPW Axle Extractor - M136 x 2.5
For removing the wheel axle with outer thread on commercial vehicles.
Extremely robust European truck repair tool applicable to :
BPW ECO Plus 8 - 12 ton
BPW ECO 10 tons new model.
Used in combinati

BPW Axle Extractor - M155 x 3.0
For removing the wheel axle with outer thread on commercial vehicles.
Extremely robust European truck repair tool applicable to :
BPW 16 ton trucks / former models.
Used in combination with 30mm and 43mm

BPW Brake Linkage Adjuster Extractor
Substantial Tool for drawing off firmly sitting BPW brake linkage adjusters.
Suitable for older and automatic linkage adjusters.
Use with 32mm wrench.
Spindle size : M22 x 1.5 x 90mm

105mm Hub Nut Socket
1in.Dr
for DAF Trucks
Drop Forged CRM

DAF Commercial Vehicle Crankshaft Alignment Tool
This heavy duty tool allows crankshaft rotation via the flywheel.
6 point drive x 24mm x 11 teeth
Applicable to 35T DAF trucks :
65CF | 75CF | 85CF | 95XF | CF75 | CF85
F65 | F75 |

DAF Engine Crankshaft Alignment Tool
1/2in. Drive
For manually rotating the engine crankshaft into position.
Applicable to : DAF XF105 / Euro5

85mm Hub Nut Socket - 1in.Dr / 12-point
for IVECO trucks and BPW / SAF trailers
Suitable for high tightening and loosening torque.
Can be used with an impact wrench or torque wrench.
Height : 60mm
External Diameter : 107.50mm

IVECO Axle Hub Nut Socket
Size : 98mm / 6 Point
Any extensive slipping is avoided.
Hex Drive: 36mm socket or spanner.
Applicable : Iveco Eurocargo and other models
For dismantling / assembly of axle nuts on commercial vehicles.

IVECO Axle Hub Nut Socket
Size : 105mm / 12 Point - across flats
Any extensive slipping is avoided.
Hex Drive: 36mm socket or spanner.
Applicable to IVECO Eurotech Cursor trucks.
For dismantling / assembly of axle nuts on commercial vehicles.

IVECO Axle Hub Nut Socket
Size : 110mm / 12 Point
Any extensive slipping is avoided.
Hex Drive: 36mm socket or spanner.
Applicable: Iveco Eurotech Cursor Ha etc
For dismantling / assembly of axle nuts on commercial vehicles.

MAN Engine Crankshaft Alignment Tool
1/2in. Drive
Length : 61mm
Allows the engine crankshaft position to be manually rotated.
Applicable to : MAN engines D20 | D25 | D26 | D28

MAN / Mercedes Crankshaft Alignment Tool
120mm Deep | 1/2in. Drive
Allows the engine crank to be manually adjusted.
Allows pinpoint accuracy calibration.
Adjusting screw in the clutch housing
Triple gear construction
Applicable to :
Mercedes Benz Actros / Atego
MAN 5-/6- and 8-cylinder engines - D25 / 28 etc.

MAN Truck Front Wheel Hub Installer
For axle bearings that are stuck due to over heating.
Can be used in conjunction with an air wrench for easier removal.
Suitable for pulling off wheel hubs with 166mm hole diameter.
Ideal European truck repair tool with extremely robust execution.
Disc size : 87 x 166 x 118mm

MAN Front Wheel Hub Tool
For Extracting / Installing wheel hubs on the front axle.
This tool makes it easier to pull out the wheel hub.
Use in conjunction with a 40mm spanner.
Inner Diameter : 50.1mm
Outer Diameter : 153.7mm

MAN Truck Axle Bearing Extractor
Inner Diameter : 107.6mm | Outer Diameter : 169mm
For removing and replacing MAN truck hub bearings.
Turn the screw and remove the old bearing.
Use with 30mm wrench
Applicable to MAN Truck Hub bearings.

MAN Truck Axle Bearing Extractor
Inner Diameter : 111mm
Outer Diameter : 169mm
Height : 240mm

For removing and replacing MAN truck hub bearings.
Use with 30mm wrench
Applicable to : MAN truck tractor 33460 / 410 / 414
with front disc brake bearing.

MAN TGA Rear Axle Extension Tube
For the removal and installation of wheel hubs.
Protects the wheel bearing and threaded bolts.
With knurling and bore for Tommy Bar.
Thread : M100 x 1.5 | Inner Size : 95mm | Outer Size : 105mm | Length: 360mm
Applicable to MAN TGA Rear Axle / HY-1350

MAN TGA Drive Shaft Nut Socket
118mm | 133mm | 3/4in.Drive | 60mm Hex
For groove nuts on MAN TGA 460 axles / V9-82L-01 / disk brake / ABS.
Designed for high tightening and release torques.
External diameter : 147.5mm
Tooth depth :

MAN TGA Front Axle Nut Socket
101mm | 110mm | 3/4in.Dr
SW60 - Six side drive
For removing the front axle nut.
Made from special steel for high tightening and loosening torque.
Overall length : 80mm
Applicable to : MAN TGA Fro

MAN / Mercedes Rear Axle Groove Nut Socket
95mm / 115mm | 3/4in. Drive
Height : 110mm
Stud width : 11.5mm
Suitable for high torque applications.
Applicable to : Mercedes / MAN - 10 / 13ton Reduction Axle
Hypoid and Trailer Ax

MAN / Mercedes Drive Axle Groove Nut Socket
101.5 x 110mm | 3/4in.Dr | 60mm Hex
With 6 teeth for removing the drive axle nut.
Suitable for high tightening and loosening torque.
Applicable to : MAN / Mercedes-Benz Trucks

MAN / Mercedes Rear Differential Nut Socket
3/4in.Dr with 6 Teeth / 8.7mm
Inner diameter : 113mm / Tooth to Tooth
Inner diameter : 126mm / Side to Side
Designed for high torque applications for
rear axle differential groove nuts o

Mercedes Axle Nut Socket
Size : 95mm / 6 Point / 157mm Long
Any extensive slipping is avoided.
Hex Drive : 36mm socket or spanner.
Applicable : Mercedes Axle Trailers

Mercedes Rear Axle Groove Nut Socket
For 6 teeth groove nuts on low-floor buses with SF portal axle AV132 -
Mercedes-Benz Citaro Bus / MAN City-Line / Neoplan / Kassbohrer
and other vehicles with identical axle.
Designed for high tight

72mm Differential Nut Socket
For loosening or tightening the castellated differential nut
used on the Mercedes-Benz Citaro and Evo Buses.
Castellated 6 Tooth Socket : 11 x 6 x 12mm deep Teeth
Outside Diameter : 84mm | Inside Diameter :

Mercedes Actros Rear Axle Groove Nut Socket
105mm | 125mm | 3/4in.Dr
Height : 180mm
Stud : 116.5mm
Stud width : 10mm
Locating tube : 60mm
Suitable for high torque applications.
Applicable to : Mercedes Benz Actros

Mercedes Benz Atego Groove Nut Socket
80mm | 95mm | 3/4in.Dr
Height : 175mm
Stud : 87mm
Stud width : 10mm
Locating tube : 49mm
Suitable for high torque applications.
Applicable to : Mercedes Benz Atego
Rear Axle / V

140mm Axle Nut Socket
For the removal of SAF Euro Axles.
Allows repair work or visual inspection of the brake
and replacement of the wheel bearing set.
Dual Hex Drive : 32mm / 46mm for use with socket or spanner.
Inner size : 140m

Scania Transmission Rear Oil Seal Tool
For installing the transmission oil seal without causing damage.
Applicable to :
SCANIA transmission flange shafts and rear axle.
e.g. Simmer Rings part : 1 502 384 / 1 502 385

Injection Valve Cap Socket
1/2in.Dr / 8 PT / 100mm Deep
Diameter : 38mm Inner | 45mm Outer
For tightening and loosening electromagnetic injection valve caps.
Applicable to : Scania / 340 Trailer

80mm Front Hub Nut Socket
1in.Dr | 8 Point
for Scania Trucks
Drop Forged CRM

Scania Engine Crankshaft Alignment Tool
1/2in. Drive
For manually rotating the engine crankshaft into position.
Applicable to : Scania Trucks up to 1996
OEM Code : 99309