Handbrake Shoe Retaining Spring Tool
with 2mm wide guide slot.
for Mercedes-Benz V-Class Vehicles.
Enables access to the retaining clips behind the rear drive flange.
For easy removal and fitting of the shoe retaining clips
on the handbrake shoes.
Applicable to : Vito / Vitano -
Typ 638 / 1996 - 2003
Typ 639 / 2003 - 2014
Typ 447 / from 2014

153mm T-Handle Assembly Hook
For Brake Springs and also Headlight units

4pc HGV Brake Caliper Socket Set
Hex 8mm | 10mm | S8 and 11PT
12mm Hex Drive
for Commercial SAF / NFZ / Knorr brake Caliper systems

Brake Caliper Socket
11pt Spline | 3/8in.Dr | 26mm Deep
For Knorr-Bremse Brake Calipers on Volvo trucks also
DAF / Foden / MAN / Mercedes / Scania / BOVA
plus BPW & SAF Trailers.

17pc Brake Caliper Socket and Bit Set
Impact Hex Bits : 7 | 8 | 9 | 11mm
Special Brake Caliper Sockets : 11.5 | 14 | 15 | 20 | 22mm
Pentagon Sockets : 10 | 12.5 | 14 | 19mm
Pentagon Bit :10mm
For use on brake Calipers when replacing the brake pads.
Applicable to : Alfa Romeo / Audi / BMW / Ford / Mercedes / Porsche.

3pc 1/2in.Dr Socket and Bit Set Brake Servicing Kit
Pentagon Profile

8pc Brake Caliper Bleed Nipple Repair Kit
Suitable for repairing Brake Caliper Bleed Nipples : M5 to M8.
Contents :
Drill : 8.5mm
Tap : 1/8in. - BSP28
6 Bleed Nipple Inserts : 1/8in.- BSP28 x 30mm

8pc Brake Caliper Bleed Nipple Repair Kit
Suitable for repairing Brake Caliper Bleed Nipples : M8 to M10.
Contents :
Drill : 10mm
Tap : M11.5 x 1.0mm
6 Bleed Nipple Inserts : M11.5 x 36mm

12pc Brake Caliper Guide Bolt Thread Repair Set
Used for repairing faulty inner threads on
brake Caliper guide bolts in wheel bearing
housing brake Caliper carriers with NO
need to remove the wheel bearings or struts.
For use on most Ford -
Vauxhall / Opel - Vauxhall | Opel and
VAG - Audi | Seat | Skoda | VW vehicles.

15pc Brake Caliper Thread Repair Set
For rethreading brake Caliper bolt holes.
With Step drill to increase hole sizes.
M12 x 1.5mm tap step drill insert locator.
Washers with centre roller bearing.
10 replacement inserts.

16pc Brake Caliper Guide Thread Repair Kit
with Titanium coated core drill
Tap and 10 threaded inserts.
Applicable to
Volkswagen - Golf MKIV / Beetle
Seat - Exeo Estate ST 170
Ford - Focus | C-Max
Vauxhall - Astra-G

5pc ABS Sensor Reamer Set - 1/4in.Dr
1/4in.Dr. / 125mm long T-Bar Handle.
4 popular sized reamers for removing dirt / dust and rust.
Sizes : 14 x 32mm | 15 x 23mm | 18 x 23mm | 18 x 34mm.
Applicable to most makes and models of vehicles.
BMW / Fiat Group / Ford / Mercedes / PSA / VAG.

5pc Elbow Connector Socket Set
Sizes : 12 | 14 | 17 | 19 | 22mm
3/8in.Dr / Single Hex and 50mm Deep
Chrome Vanadium
Suitable for L-type pipe fittings on trucks.
Suitable for construction equipment and general machinery.

Manual Tube Expander
7-in-1 Pipe Expander for copper and aluminium tubing.
Sizes : 6 | 8 | 10 | 12 | 16 | 19 | 22mm
1/4 | 5/16 | 3/8 | 1/2 | 5/8 | 3/4 | 7/8in.
Made of heavy duty alloy steel for a long working life.

Universal Flaring Too Kit
Adjustable | 5 - 16mm
For creating conical / tapered flares.
For Brass or Aluminium pipes.
Size range : 5 - 16mm | 3/16 - 5/8in.

Micro Brake Pipe Flaring Tool - 3/16in. SAE
For Copper / Cupronickel and Steel Pipes.
Hand-held brake pipe flaring tool that is capable of forming both
SAE single and double flares in 3/16in. / 4.75mm diameter pipes.
The compact design makes it ideal for on vehicle use and
allows for it to fit in an engine bay or under a wheel arch
when replacing or repairing a brake pipe.
High-pressure punch grease also included to lubricate friction surfaces.

6pc Pipe Flaring Kit
Steel Compressor Yoke : 3/16 | 1/4 | 5/16 | 3/8 | 1/2 | 5/8in.
Flaring Tool
Flexible Tube Benders
Tube Cutter 3 - 28mm

6pc Brake Pipe Flaring Kit
With Quick Release Dies
Brake Flaring Tool Suitable For 3/16in. or 4.75mm Diameter Tubing
Secure Clamping with Quick Release.

7pc Flaring Tool Set
For Single or Double Flaring Aluminium and copper tubing
Adaptors for 3/16 | 1/4 | 5/16 | 3/8 | 1/2in. Tube or 4.8 - 12.7mm

10pc Pipe Flaring Kit
Steel Compressor Yoke
Flaring Tool
Flaring Dies - 5. 6. 8. 10. 12. 14. 16mm

Copper Tube Flaring Tool Kit
Imperial : 1/4 | 5/16 | 3/8 | 1/2 | 5/8 | 3/4in.
Metric : 6 | 8 | 10 | 12 | 16 | 19mm
Suitable for soft copper, aluminium, brass and other soft metals.
Allows easy and smooth operation saving time and energy.
Off-centre mounted cone spins on an axis for a uniform shape.
Arc frame ergonomic yoke designed with double ring bar
guarantees a professional job with permanent levelling.
Include tools for shortening or de-burring
and 45 degree single flaring of pipes.

Professional Brake Line Flaring Tool Kit
For flaring brake pipes and hydraulic tubing.
Can be used on copper / brass / aluminium and steel pipes
For coated and non-coated pipes.
For inside and outside flaring.
Includes 4 pairs of pressure pieces :
4.75mm | 6.35mm | 8mm | 9.5mm
3/16in. | 1/4in. | 5/16in. | 3/8in.

15pc Comprehensive Brake Service Tool Set
Brake Line Flare Nut Wrench
Brake Spring Pliers and Spring Tool
Pound Thru Screwdriver and Hex Socket Bits
Brake Caliper File and Brushes
Brake Cable Hook
Assembly Tool

Brake Drum Gauge
Size Range 160mm - 360mm
Metric and Imperial Scale.
Developed to measure the wear limit on brake drums
as well as the diameter of the drum and then establish
the shoe position prior to drum re-fitting.
For o

8pc Brake Gauge Set
Colour coded for ease of use
Green for Go : 8mm | 10mm | 12mm
Yellow for Caution : 4mm | 5mm | 6mm
Red for stop and replace : 2mm | 3mm

100mm Digital Brake Disc and Drum Caliper
For measuring external brake disc thickness and internal small drums.
Easy Read Digital LCD Display - 11mm high characters.
Metric or Imperial read-out with Hold function.
Range : 0 - 100mm / 0 - 4in.
Resolution : 0.01mm / 0.0005in.
Battery : SR44-1.5V - supplied.

150mm Digital Brake Disc and Drum Caliper
Measures external brake disc and internal small drums
LCD display with 11mm high figures for easy reading
Metric or Imperial read-out with Hold function
Supplied with calibration certificate and storage case
Range : 0 - 150mm / 0 - 6in.
Resolution : 0.01mm / 0.0005in.
Battery : 1.5V SR44 - supplied

3pc Brake Disc Run Out Kit
Allows the DTi gauge to be mounted in almost any position
against the brake disc to measure disc warp.
DTi Gauge accurate to 0.01mm / total deflection 10mm.
The Locking pliers allow fixing to suspension bracket or component part
Segmented Steel Mounting Post can be bent and locked into position.
Universal - measures brake disc drive flange or any rotating component run-out.
Can be used on motorcycles.

Dial Test Indicator & Precision Point Set
0 - 10mm Dial in 0.01mm increments.
Magnetic base with fine adjustment.
Magnet has a 60kg pull.
On / Off Switch for easy positioning.
Used to check variations in machined parts.
Ideal for checking run-out on disc brakes.

5pc Wheel Cylinder Cup / Seal Installation Rocket Set
Tapered Cones enable wheel cylinder o-rings and seals
to be installed easily without damage to the brake cylinder assembly.
Sizes :
1 - 3/4'' | 44.5 / 47.5mm
1 - 7/8'' | 48 / 51mm
2 - 1/8'' | 54 / 57mm
2 - 3/16'' | 56 / 59mm
2 - 5/16'' | 59 / 62mm

Universal Wheel Axle Nut Remove and Installation Kit
Engineered to loosen and tighten the rear wheel nut.
Both sides of pin are adjustable.
3 sets of pins for different vehicles.
For vehicles over 2 tons with circular nuts.
Pins : 5.5 | 6.8 | 9.1mm / Nut : M8 x P1.25

3pc Rear Axle Bearing Puller Set
Sizes : 1in. to 1-7/8in. | 1-5/16in. to 2-3/8in. | 1-3/8in. to 2-7/8in.
Allows for the easy removal of Semi-Floating Rear Axle Bearings
Suitable for most domestic vehicles

8pc Rear Axle Bearing Puller & Slide Hammer Set
With Small / Medium and Large Bearing Puller Adaptors
cover inner diameters from 1 to 1-7/8 | 1-5/16 to 2-3/8 | 1-3/8 to 2-7/8
respectively to remove semi-floating rear axle bearings.
Safely repair rear axle problems on the majority of domestic cars and light trucks.

3pc Rear Axle Tool Set for Mercedes-Benz
with Spline Bits : M10 | M12
For making tracking adjustments to the rear axle on
Mercedes-Benz vehicles without removing the plastic covers.
Double angled shaft to access hard to reach adjustment screws.
Suitable for Mercedes-Benz C-Class / W203 and S-Class
and older models with under body panels and vehicles with level sensors.

Rear Axle Locking Nut Spanner
For loosening and tightening the wheel bearing grooved lock nut
when replacing wheel bearings on rear axle shafts or full floating axles.
Applicable to : Mercedes Sprinter / W901 - W905 rear axles.
Can be used with a 1/2in.Dr Ratchet or Power Bar.

Rear Axle Locking Nut Spanner
For removing and replacing the wheel bearing grooved lock nut
when replacing wheel bearings on rear axle shafts or full floating axles.
Applicable to : Mercedes Sprinter / W901 - W905 rear axles.
Can be used with a 1/2in.Dr Ratchet or Power Bar.

4pc Rear Wheel Bearing Service Set
For removing / installing the rear wheel bearing and rear axle flange on
Mercedes vehicles : W124 | W129 | W201 W202

16pc Slide Hammer / Puller Set
Combination Puller with 5lb Malleable Steel Slide Hammer
Drop Forged Steel Pullers and Attachments
Converts to 2 or 3 Jaw Internal / External Pullers

9pc Mini Bearing Separator Set
Compact set containing
Bearing Separator and 2 Leg Puller
Suitable for removing small gears
wheels and shaft fittings.
Separator : 15 - 58mm
Puller Jaw : 50mm

Bearing Puller Kit with Ball Ended Puller Adaptor
Suitable for removal of a variety of blind bearings
where traditional bearing and gear pullers will not reach.
Ball-end tips fit inside bearing races to provide traction for bearing extraction.
Bearing Sizes : 5 / 6 / 8 / 9 / 11 / 12.5mm

Small Insert Bearing Puller Kit
For the removal of bearings where other pullers are unable to be used
by locking into the bearing race itself.
Adjustment range : 20 - 90mm
Interchangeable heads : 5.5 / 6.0 and 8.0mm diameter
Puller yoke and Forcing screw
2 Legs and Extensions
Centre screw thread cap
6 Ball ended threaded puller adaptors

Small Universal Press Support Ring
Outer diameter : 115mm
Inner diameter : 100mm
Height : 160mm
Wall : 7.5mm
Capacity : 10T
for the removal of Wheel Bearings / Bushings and Hubs
Usually working in combination with a hydraulic press.
Great alternative to traditional V blocks and old bearing casings.
Can be used with Universal press support blocks / not included.

Medium Universal Press Support Ring
Outer diameter : 140mm
Inner diameter : 120mm
Height : 160mm
Wall : 10mm
Capacity : 40T
for the removal of Wheel Bearings / Bushings and Hubs
Usually working in combination with a hydraulic press.
Great alternative to traditional V blocks and old bearing casings.
Can be used with Universal press support blocks / not included.

Large Universal Press Support Ring
Outer diameter : 180mm
Inner diameter : 160mm
Height : 160mm
Wall : 10mm
Capacity : 40T
for the removal of Wheel Bearings / Bushings and Hubs
Usually working in combination with a hydraulic press.
Great alternative to traditional V blocks and old bearing casings.
Can be used with Universal press support blocks / not included.

3pc Universal Press Support Ring Set
Diameters : 115mm / 100mm | H : 160mm | W : 7.5mm | Cap :10T
Diameters : 140mm / 120mm | H: 160mm | W : 10mm | Cap : 40T
Diameters : 180mm / 160mm | H: 160mm | W: 10mm | Cap : 40T
for the removal of Wheel Bearings / Bushings and Hubs
Usually working in combination with a hydraulic press.
Great alternative to traditional V blocks and old bearing casings.
Can be used with Universal press support blocks / not included.

30pc Master Press and Pull Sleeve Kit
For the installation of bushes / bearings and seals
For both cars and light commercial vans.
Inside Diameters 34 - 72mm in 2mm steps
Outside Diameters 44 - 82mm in 2mm steps
Pulling Spindles M10 . M12 . M14 . M16.

26pc Universal Press and Pull Sleeve Kit
For the removal and installation of bushes / bearings and seals etc.
22 x Press Sleeves inside diameter from 34-80mm in 2mm steps
Outside diameter from 44-90mm in 2mm steps
M10. M12. M14. M16 Pulling Spindles

Universal Press and Pull Sleeve Kit
Press Sleeves from 34 - 80mm Diameter in 2mm steps
Outside Diameter from 44 - 90mm in 2mm steps
5 x Pulling Spindles with nuts and thrust bearings
M10 | M12 | M14 M16 | M18

Replacement M10 Pulling Spindle
for Universal Press and Pull Sleeve Kits CT2934 or CT3187 or CT3757

Replacement M12 Pulling Spindle
for Universal Press and Pull Sleeve Kits CT2934 or CT3187 or CT3757