CT6385
Auxiliary Belt Tension Set
5pc Auxiliary Belt Tension Set
for Ford and PSA Diesel Engines.
Provides a safe and controlled method of adjusting the
tensioner position during removal and installation of the auxiliary belt.
Includes various adaptors along with an extension bar
to allow an extended reach on the raised peg which
can then be used with and appropriate tensioner wrench
and low profile thin walled socket.
Applicable to : 1.4 | 1.5 | 1.6 | 2.0 | 2.2 Diesel Engines.
CT6358
Auxilliary Belt Tensioner Tool
Mercedes Auxilliary Belt Tensioner Tool
For tensioning and loosening the damper spring without damage.
on Mercedes-Benz W169 | W245 Engines
with air conditioning and / or stop-start function :
Suitable for following vehicles :
A-Class W169 / 2004 - 2012
A150 | A160 | A170 | A180 | A200 | A200T
B-Class W245 / 2005 - 2011
B150 | B160 | B170 | B180 | B200 | B200T
OEM Code : 266589003100
CT6286
Oil Pump / Balance Shaft Alignment Kit
Oil Pump / Balance Shaft Alignment Kit
for BMW 1 | 2 | 3 | 4 Series - 6L / 2.0L Petrol Engines.
For fixing the balance shaft and holding the chain sprocket
when used for repairing the chain and sprocket wheel drive.
Applicable to Engine Codes : N20 | N26 2012 - 2017
OEM Codes : 2 212 825 | 2 318 117 | 11 4 120
CT6431
Timing Tool Set - Vauxhall / Opel
Vauxhall / Opel Timing Tool Set
For 1.6 SIDI | SIDI Turbo | SIDI Turbo EcoFLEX Engines
For checking and setting the engine timing when replacing the timing chain.
Camshaft Alignment Tool
Crankshaft Pulley Holding Tool
Balance Shaft Sprocket Locking Tools
Chain Tensioner Locking Pin
CT6449
Water Pump Sprocket Retainer
Water Pump Sprocket Holding Tool
for GM Ecotec engines.
Holds the timing chain and gear in place while
removing or installing water pump on
Chevrolet / Opel / Vauxhall Ecotec engines.
Simply remove access plate from front cover and install the tool.
OEM Code : EN-43651.
CT6421
Camshaft Drive Tensioner Wrench - VAG
VAG Camshaft Drive Tensioner Wrench
For adjusting the Camshaft drive belt tensioner on
VAG Vehicles with 1.0 / 1.2 / 1.4 turbo charged engines.
Applicable to :
Audi - A1 / A3
Seat - Mii / Leon
Skoda - Octavia / Citigo
Volkswagen - Up / Golf V11
OEM Code : T10499
CT6296
Air Conditioning System Test Kit
Air Conditioning System Test Kit
For testing automotive air conditioning systems using R1234YF
refrigerant only by comparing the high and low pressure readings.
60mm gauges with tough rubber protective guard with 7/16in. copper coupler
Low : -30 - 120 psi / -1 - 8 bar
High : 0-500 psi / 0 - 35 bar
Blue Hose - 1/4in. FFL x 50in.
Red Hose - 1/4in. FFL x 50in.
Yellow Hose - 1/2in. ACME x 50in.
Sight glass for viewing condition of refrigerant.
CT6360
Pipe Line Stopper Kit - 4pc
4pc Pipe Line Stopper Kit
Sizes : Banjo | 3/8 | 5/16 | 1/2 Inch
Spring loaded design for use with all Automotive Fluids.
Use to plug steel lines once disconnected.
Prevents fluid leaks and contamination during service.
Use with any automotive fluid.
Spring loaded design installs in seconds.
CT6404
Cooling System Pressure Test Kit
5pc Universal Cooling System Pressure Test Kit
Four universal cone adaptors fit a wide range of vehicles.
Hand pump with gauge allows simple and easy controlled testing.
Release pin allows depressurisation prior to detachment.
Contents:
Pressure pump
Cone adaptors : 17-24mm | 28-31.5mm | 37-39.5mm | 47-48.5mm
Cone adaptor system for sealing and pressurising the cooling system.
CT6146
Tube & Trim Cutter Set
Professional Multi-Angle Cutter Set
Multi-Angle Cutting Pliers with Wire Slot Cutters.
For Water Pipes / Line Pipes / Edge Banding Strip etc.
With Spare Blade and Small Open End Wrench.
Sturdy steel frame with plastic cover handle for comfortable diagonal cutting.
Multi-angle Anvil with : 45 | 60 | 75 | 90 | 105 | 120 Degree angles
For Pipes : 17 - 20 - 27mm
CT6405
Fluid Extractor - 9L
9L Manual Fluid Extractor
Suitable for extracting oil from vehicles and industrial machinery
also suitable for low-viscosity fluids such as water.
Automatic safety shut off mechanism when the tank is full.
Supplied with 3 tubes : 4mm / 6mm / 10mm Diameter.
Not for use with Toxic or Volatile Liquids.
CT6365
Oil Sump Plug Key Set - 9pc
9pc Oil Sump Plug Keys
Special Profile Set for assembly and disassembly of
plastic oil drain screws on plastic oil sumps.
Supplied with 3/8in.Dr T-handle or use with 17mm Socket.
For manual operation - do not use power tools.
Applicable to : Ford / PSA / BMW / VAG / Mercedes / DAF / MAN / GM.
CT6058
Pipe Plug Socket Set - 11pc
11pc 3/8in.Dr Pipe Plug Socket Set
Male : 3/16 | 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Female : 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Tapered Male Square Drive and
Chamfered Female Square Drive aligns socket to fastener quickly
Low profile design provides easy access to tight spaces
Fits any 3/8in.Dr ratchets, bars etc.
Chrome-Molybdenum for high torque impact tools.
CT6269
Oil Filter Housing Wrench - 74.5mm
74.5mm Oil Filter Wrench - 15pt / 3/8in.Dr
For Ford 1.5 | 1.6 EcoBoost Engines
Allows the correct removal and fitment of the fuel filter housing
matching the fuel canister designed filter.
With offset design ideal for use in confined areas.
Applicable to : C-Max II | Focus III | Galaxy III
Kuga II | Mondeo IV / V | S-Max II | Transit Connect II.
CT6368
Dual Clutch Oil Seal Fitting Kit
DCT Wet Clutch Oil Seal Fitting Kit
For Ford and Volvo vehicles fitted with the Dual Wet Clutch System
also vehicles with Getrag MPS6 / 6DCT 450 gearboxes.
Includes the seal guide and cover press used for
the fitting of the clutch cover without damaging the centre seal.
OEM Codes : 308-764 | 308-783 | 9997383 | 9997388.
CT6361
DSG Clutch Installation Kit - Ford
DSG Dual Clutch Transmission Tool Kit
Ford Focus DCT Dual Clutch Transmission DPS6
Specially designed to disassemble and install dry transmissions
It re-springs / re-trips the springs on the clutch so that you can reinstall it again.
Fiesta 2011 - 2019
Focus 2012 - 2018
Transit Connect 2019
B-MAX since 2012
OEM Code : 307675
CT6425
CV Joint Boot Clamp Pliers
Offset CV Joint Boot Clamp Pliers
Special Boot Clamp Crimping Pliers designed to work in confined spaces
allows you to work on large size boot clamps / top plate on pliers flatten the crimp.
The pliers work from the side - head is turned 90 degrees
unlike traditional tools that work from the end.
Use on eared clamps and Perma-Quick type clamps
used on fuel filters / cooling systems and vacuum lines.
Length : 245mm
Max. Clamping Width : 31mm
CT6382
Inner Drive Shaft Extractor Fork
Inner Drive Shaft Extractor Fork
for Ford / Volvo / Renault / Mazda etc.
Contact Lever Diameter : 55mm.
Jaw Diameter : 85mm.
Length : 380mm.
Designed to allow for the quick and safe removal of drive shafts
by connecting properly with the locking clip rings found on many
front wheel drive vehicles preventing damage to the
drive shaft and surrounding components.
CT6410
Differential Flange / Insert Nut Tool Set
BMW Differential Flange / Insert Nut Tool Set
For removing and installing of the drive shaft nut.
Allows inserting of the rear differential pinion seal.
Suitable for BMW vehicles with rear and four wheel drive.
HAG 215 Sp / HAG 220kom / HAG 225kom / HAG type G
Open End Spanner - 50mm
Flange Holding Tool
Multi-Point Ring Spanner - 65mm
Multi-Point Socket - 34T
Seal Ring Drift
CT6379
Suspension Nut Wrench - VAG
13mm Suspension Top Mount Nut Wrench
for VAG - Audi | Seat | Skoda | VW
13mm 6 / 8 point Dual Sided Swivel Socket
120mm Total Length with 3/8in.drive.
Specialist tool designed to be used when
removing the top of Macpherson strut mounts.
Flexible for hard to reach parts allowing access
to the strut mount with minimal effort due to the flexible design.
CT6228
Brake Fluid Bleed System - Electric
Electric Brake Fluid Bleeder
For most makes and models of vehicles
With Adjustable pulse oil change which can effectively
clean the pipeline and change the oil more thoroughly.
Contents : Brake Fluid Bleeder / 2L Bottle & 3.5M Hose / 3 Adaptors.
Power supply : 240V | 50 / 60Hz | 35W
Output Pressure : 0.6 - 3.0 Bar
Output flow : <= 1.2L / Min
Noise Level : 70 Db
Device shuts off when container is empty
CT6293
Bearing Puller Set
Bearing Puller Kit with Ball Ended Puller Adaptor
Suitable for removal of a variety of blind bearings
where traditional bearing and gear pullers will not reach.
Ball-end tips fit inside bearing races to provide traction for bearing extraction.
Bearing Sizes : 5 / 6 / 8 / 9 / 11 / 12.5mm
CT6357
Wheel Bearing Ring Puller - 68mm
68mm Bearing Inner Ring Puller
For removing the inner wheel bearing rings on wheel hubs.
The bearing rings usually remain on the wheel hub
when the wheel bearings are removed.
Integral Clamp holds the puller legs
securely behind the component to be removed.
Pressure piece diameter : 25 x 30mm
Puller width : 68mm
Puller depth : 60 mm
CT6292
Bearing Separator Set
Bearing Separator
Drop forged
Clamping Width : 46mm - 230mm max
Clamping Bolt Length : 350mm / Distance : 224mm / Thread : M25 x 2.5
Puller Bolt : 3/4in. x 10 UNC
Puller Bolt distance : 164mm / 350mm max
Splitting Knife Base : 102mm - 288mm max
Suitable for removing bearings / gears and bushings from shafts.
CT6267
Tyre Bead Retainer
Tyre Bead Retainer
With High Density Rubberized PVC Coating -
prevents the tyre bead from creeping when mounting the top head.
Solid metal core construction is extremely durable.
Easily clips into place with one hand - use with tyre spoons or tyre lever.
Suitable for all tyres.
Ideal for use with CT6266.
CT6160
EV / Hybrid Vehicle Warning Sign
EV / Hybrid Warning Sign
3 Sided with Magnetic Base
Made of hard-wearing plastic.
Weather & scratch resistant.
With water drain hole in the bottom.
Magnet moulded in to plastic sign to prevent scratches.
Designed to serve as a warning that a vehicle is EV or Hybrid
CT6161
EV / Hybrid Vehicle Warning Sign
EV / Hybrid Warning Sign
3 Sided with Magnetic Base
Made of hard-wearing plastic.
Weather & Scratch resistant.
With water drain hole in the bottom.
With suction cup - suitable for indoor and outdoor use.
Designed to serve as a warning that a vehicle is EV or Hybrid
CT6435
Mechanics Vehicle Wing Cover
Mechanics Vehicle Wing Cover
With 4 pockets for holding tools while working on car.
Wing cover held in place by integral magnets.
PVC material prevents scratching and marking of paintwork.
Protects vehicle body from damage while being serviced or repaired.
Size : 1200 x 1000mm
CT0681
Tool Trolley - 3 Shelves
Folding Garage / Workshop Trolley
Easy access for adding or removing items to and from trolley.
4 Large Castor Wheels with 2 locking.
Overall Size : 640mm W x 375mm D x 830mm H
Shelf Size : 595mm W x 370mm D x 35mm H
Capacity : 30kg per shelf
Folds up in seconds for easy storage when not in use.
Can also be used as a janitorial trolley.
Cannon Tools Limited • 20 Station Road, Rowley Regis, West Midlands, B65 0JU, United Kingdom
T +44 (0) 121 561 6760