Petrol Injector Puller for Ford Vehicles
For removing Bosch GDI Injectors
on all standard Ford EcoBoost petrol engines 1.0 - 3.7 litre capacity.
Extracts petrol injectors easily without damaging the injector or head.
Includes slide hammer and specially designed injector claw.
OEM Code : 310-206

Fuel Injector Puller Set
for Alfa Romeo / Fiat / Ford / Iveco / Opel / PSA / Suzuki
1.3 / 1.6 / 1.9 / 2.0 - 16 Valve Engines - Also 2.3 and 3.0 models
Specifically designed for the removal of extremely seized injectors.
With the application-specific extractor -
the injectors can be removed either hydraulically or mechanically.

Fuel Pump Sprocket Puller
for Ford Transit 2.2L TDCi
From 2011 fuel pump sprockets no longer have threaded holes fitted in them
this tool allows the pump removal without removing the timing chain.
Applicable to : Ford Transit from 2011 with 2.2L TDCi Puma engine.
Also Land Rover Defender 2.2L TD4 / 2001 - 2015
OEM Codes : 303-249 | 303-249/01

5pc Fuel Pump Water Drain Valve Plugs
For Ford 6.7 | 6.7L Diesel HFCM
Ford Truck / Pickup 2017-2022
F250 / F350 / F450 / F550 Super Duty 6.7L V8 Diesel Engines.
Easy Installation.
OEM Code : HC3Z-9J305-A

370mm Heavy Duty Injector Gasket Puller
with 840g Slide Hammer
For extracting burnt in copper seal washers from the injector shaft.
4 - 16mm Internal Diameter Seal Rings.
Helps to avoid damages to the cylinder heads.
Applicable to : BMW / Mercedes-Benz / PSA models.

Injector Seat and Shaft Cleaning Kit
Used to remove rust / carbon and other debris
and efficient cleaning of injector seats and shafts on diesel engines.
Suitable for a wide range of vehicles and engines.
With Wire Brushes : 25.1 | 29.5 | 30.2 | 34.9mm
2 Stage Wire Brushes : 12.1 | 19.1 | 25.4mm
Bore Wire Brushes : 8 | 10 | 12 | 15 | 17 | 19mm
Brush Handle and Rigid Extension with quick couplers
Flexible Extension with fixing screw - 1/4in. Hex Drive
Cleaning Swab Assortment : 5 - 16mm
Used to remove rust / carbon and other debris.

85pc Assorted Leak Off Connectors
Suitable Connectors for Bosch / Siemens / Delphi Injectors.
T Type for PA Tube
T Type for Rubber Tube
L Type for PA Tube
Offset for Rubber Tube
90 degree for Rubber Tube
102 degree for PA Tube
Snap Lock Delphi Type for PA Tube

Motorcycle Compression & Fuel Pressure Gauge Set
3 Gauges with Connectors and Adaptors for
testing motorcycle compression and fuel pressure.
Compression : 0 - 300psi | 0 - 2000kPa.
Fuel Pressure : 0 - 7bar | 0 - 1000psi.
Fuel Low Pressure : 0 - 1bar | 0-100kPa.
Spark plug sizes : 8 | 10 | 12 | 14mm.
Hose length : 200mm.
Fuel connector sizes: 6.4 | 7.9mm Diameter.
Adaptors : M8 | M10 | M12 | M14.

Small Engine Valve Spring Compressor
Range : 3/4in. to 1-1/16in.
With 2 Jaw Sizes.
Heavy-duty frame and screw for rigidity.
Simple and Robust for -
Briggs and Stratton / Clinton / Harley-Davidson etc.

Intermediate Lever Spring Removal Tool
for BMW N13 / N16 / N20 / N26 / N52 / N55
Designed to remove and install the intermediate shaft control spring
used in the VVT system found on BMW petrol engines.
BMW 1 / 2 / 3 / 4 / 5 / 6 Series | X1 and X3
Engine Codes :
N13 | N16 / 1.6L | N20 / 1.6 / 2.0L
N26 / 2.0L and N52 | N55 / 3.0L petrol engines.
OEM Code : 11 7 110

Multi-Valve Spring Compressor
Universal Jaw with 55 - 175mm capacity and 165mm throat depth.
For use on petrol and diesel engines with deep-seated valves.
Suitable also for general use on OHC / OHV and CVH engines.
Reversible jaw and adaptor.
Twin cam action permits use from above or below valve.

5pc Auxiliary Belt Tension Set
for Ford and PSA Diesel Engines.
Provides a safe and controlled method of adjusting the
tensioner position during removal and installation of the auxiliary belt.
Includes various adaptors along with an extension bar
to allow an extended reach on the raised peg which
can then be used with and appropriate tensioner wrench
and low profile thin walled socket.
Applicable to : 1.4 | 1.5 | 1.6 | 2.0 | 2.2 Diesel Engines.

Mercedes Auxilliary Belt Tensioner Tool
For tensioning and loosening the damper spring without damage.
on Mercedes-Benz W169 | W245 Engines
with air conditioning and / or stop-start function :
Suitable for following vehicles :
A-Class W169 / 2004 - 2012
A150 | A160 | A170 | A180 | A200 | A200T
B-Class W245 / 2005 - 2011
B150 | B160 | B170 | B180 | B200 | B200T
OEM Code : 266589003100

BMW Crankshaft Seal Tool Set
For removing and installing the front and rear crankshaft seal.
Applicable to :
N20 / N26 / N40 / N42 / N45 / N45T
N46 / N46T / N52 / N53 / N54 / N55
OEM Codes :
110370 | 119181 | 119182 | 119183
119184 | 119220 | 119222 | 119230 | 119231
119233 | 119235
119601 | 2212822 | 2212827

Oil Pump / Balance Shaft Alignment Kit
for BMW 1 | 2 | 3 | 4 Series - 6L / 2.0L Petrol Engines.
For fixing the balance shaft and holding the chain sprocket
when used for repairing the chain and sprocket wheel drive.
Applicable to Engine Codes : N20 | N26 2012 - 2017
OEM Codes : 2 212 825 | 2 318 117 | 11 4 120

Fiat Timing Tool Set
Alfa Romeo / Fiat / Lancia 0.9 Twin Air Engines
For adjusting the engine timing when replacing
the timing chain or cylinder head repairs etc.
Crankshaft Locking Pin
Belt Pulley Locking Pin
Camshaft Locking Plate
Engine Code : 312A2000

Timing Tool Set - Mercedes M282
For timing chain replacement and setting the timing on
Mercedes 1.3M 242.914 and Renault 1.3 LH5H -
chain driven twin camshaft 4 cylinder 1.3 Petrol Engines
OEM Code : 282589002300

4pc Camshaft Adjuster Set
for Mercedes V6 / V8 - M152 / M157 / M276 / M278 Vehicles
Camshaft Position Sensor Reluctor Setting Tools
Used to mark pulse wheel on removed camshaft.
Can be used in conjunction with CT4076
OEM Code : 278589002300

Diesel Engine Timing Tool Kit
for Citroen / Peugeot / Opel / Vauxhall
Fiat / Ford / Mazda / Renault / Volvo
With Flywheel Locking Pin
Injection Pump Locking Pins
Tensioner Retaining Tool

Vauxhall / Opel Timing Tool Set
For 1.6 SIDI | SIDI Turbo | SIDI Turbo EcoFLEX Engines
For checking and setting the engine timing when replacing the timing chain.
Camshaft Alignment Tool
Crankshaft Pulley Holding Tool
Balance Shaft Sprocket Locking Tools
Chain Tensioner Locking Pin

Water Pump Sprocket Holding Tool
for GM Ecotec engines.
Holds the timing chain and gear in place while
removing or installing water pump on
Chevrolet / Opel / Vauxhall Ecotec engines.
Simply remove access plate from front cover and install the tool.
OEM Code : EN-43651.

VAG Camshaft Drive Tensioner Wrench
For adjusting the Camshaft drive belt tensioner on
VAG Vehicles with 1.0 / 1.2 / 1.4 turbo charged engines.
Applicable to :
Audi - A1 / A3
Seat - Mii / Leon
Skoda - Octavia / Citigo
Volkswagen - Up / Golf V11
OEM Code : T10499

Special Socket
8 Point | 100mm Deep | 3|8in.Dr
For loosening and tightening intake manifold fastening screws.
Applicable to : Mercedes | Nissan | Opel | Renault Vehicles
with 1.6 DCi | CDTi Engines

High Pressure Adjustable Quick Coupler
Adapter for A/C manifold gauge set / R1234YF type.
Quick and easy connect / disconnect
Protection sleeve to provide safety protection
to avoid injury and refrigerant loss, defending against leakage.

Low Pressure Adjustable Quick Coupler
Adapter for A/C manifold gauge set / R1234YF type.
Quick and easy connect / disconnect
Protection sleeve to provide safety protection
to avoid injury and refrigerant loss, defending against leakage.

Air Conditioning System Test Kit
For testing automotive air conditioning systems using R1234YF
refrigerant only by comparing the high and low pressure readings.
60mm gauges with tough rubber protective guard with 7/16in. copper coupler
Low : -30 - 120 psi / -1 - 8 bar
High : 0-500 psi / 0 - 35 bar
Blue Hose - 1/4in. FFL x 50in.
Red Hose - 1/4in. FFL x 50in.
Yellow Hose - 1/2in. ACME x 50in.
Sight glass for viewing condition of refrigerant.

4pc Pipe Line Stopper Kit
Sizes : Banjo | 3/8 | 5/16 | 1/2 Inch
Spring loaded design for use with all Automotive Fluids.
Use to plug steel lines once disconnected.
Prevents fluid leaks and contamination during service.
Use with any automotive fluid.
Spring loaded design installs in seconds.

5pc Universal Cooling System Pressure Test Kit
Four universal cone adaptors fit a wide range of vehicles.
Hand pump with gauge allows simple and easy controlled testing.
Release pin allows depressurisation prior to detachment.
Contents:
Pressure pump
Cone adaptors : 17-24mm | 28-31.5mm | 37-39.5mm | 47-48.5mm
Cone adaptor system for sealing and pressurising the cooling system.

Professional Multi-Angle Cutter Set
Multi-Angle Cutting Pliers with Wire Slot Cutters.
For Water Pipes / Line Pipes / Edge Banding Strip etc.
With Spare Blade and Small Open End Wrench.
Sturdy steel frame with plastic cover handle for comfortable diagonal cutting.
Multi-angle Anvil with : 45 | 60 | 75 | 90 | 105 | 120 Degree angles
For Pipes : 17 - 20 - 27mm

9L Manual Fluid Extractor
Suitable for extracting oil from vehicles and industrial machinery
also suitable for low-viscosity fluids such as water.
Automatic safety shut off mechanism when the tank is full.
Supplied with 3 tubes : 4mm / 6mm / 10mm Diameter.
Not for use with Toxic or Volatile Liquids.

5L Lockable Jerry Can
Suitable for use on Motorcycles.
Rust Proof / Crush Resistant and Non-Corroding
Designed with ventilation holes to prevent negative pressure backflow.
External pressure up to two tons - altitude drop without deformation.
Could be installed on mount or roof rack.
Material : High-density Polyethylene Plastic
Automatic Shut-off Nozzle.

9pc Oil Sump Plug Keys
Special Profile Set for assembly and disassembly of
plastic oil drain screws on plastic oil sumps.
Supplied with 3/8in.Dr T-handle or use with 17mm Socket.
For manual operation - do not use power tools.
Applicable to : Ford / PSA / BMW / VAG / Mercedes / DAF / MAN / GM.

11pc 3/8in.Dr Pipe Plug Socket Set
Male : 3/16 | 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Female : 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Tapered Male Square Drive and
Chamfered Female Square Drive aligns socket to fastener quickly
Low profile design provides easy access to tight spaces
Fits any 3/8in.Dr ratchets, bars etc.
Chrome-Molybdenum for high torque impact tools.

5pc Ford Plastic Oil Drain Plug Set
Replacement Nylon Oil Drain Plugs for Ford vehicles.
Heavy Duty Plastic Plug.
OEM Code : 1830727

5pc Oil Drain Plastic Plug Set
Replacement Nylon Oil Drain Plugs for Mercedes Benz vehicles.
Complete with sealing ring.
OEM Code : A0029902017

5pc Oil Drain Plastic Plug Set
Replacement Nylon Oil Drain Plugs for VAG vehicles.
Also suits CAM cover on 1.6 / 2.0 TDI diesel engines.
OEM Code : 06L 103 801.

74.5mm Oil Filter Wrench - 15pt / 3/8in.Dr
For Ford 1.5 | 1.6 EcoBoost Engines
Allows the correct removal and fitment of the fuel filter housing
matching the fuel canister designed filter.
With offset design ideal for use in confined areas.
Applicable to : C-Max II | Focus III | Galaxy III
Kuga II | Mondeo IV / V | S-Max II | Transit Connect II.

DCT Wet Clutch Oil Seal Fitting Kit
For Ford and Volvo vehicles fitted with the Dual Wet Clutch System
also vehicles with Getrag MPS6 / 6DCT 450 gearboxes.
Includes the seal guide and cover press used for
the fitting of the clutch cover without damaging the centre seal.
OEM Codes : 308-764 | 308-783 | 9997383 | 9997388.

DSG Dual Clutch Transmission Tool Kit
Ford Focus DCT Dual Clutch Transmission DPS6
Specially designed to disassemble and install dry transmissions
It re-springs / re-trips the springs on the clutch so that you can reinstall it again.
Fiesta 2011 - 2019
Focus 2012 - 2018
Transit Connect 2019
B-MAX since 2012
OEM Code : 307675

Offset CV Joint Boot Clamp Pliers
Special Boot Clamp Crimping Pliers designed to work in confined spaces
allows you to work on large size boot clamps / top plate on pliers flatten the crimp.
The pliers work from the side - head is turned 90 degrees
unlike traditional tools that work from the end.
Use on eared clamps and Perma-Quick type clamps
used on fuel filters / cooling systems and vacuum lines.
Length : 245mm
Max. Clamping Width : 31mm

Inner Drive Shaft Extractor Fork
for Ford / Volvo / Renault / Mazda etc.
Contact Lever Diameter : 55mm.
Jaw Diameter : 85mm.
Length : 380mm.
Designed to allow for the quick and safe removal of drive shafts
by connecting properly with the locking clip rings found on many
front wheel drive vehicles preventing damage to the
drive shaft and surrounding components.

BMW Differential Flange / Insert Nut Tool Set
For removing and installing of the drive shaft nut.
Allows inserting of the rear differential pinion seal.
Suitable for BMW vehicles with rear and four wheel drive.
HAG 215 Sp / HAG 220kom / HAG 225kom / HAG type G
Open End Spanner - 50mm
Flange Holding Tool
Multi-Point Ring Spanner - 65mm
Multi-Point Socket - 34T
Seal Ring Drift

62mm Ball Joint Remover
3/4in.Dr for Cars / Light Trucks and SUVs
Opening on the support fork : 62mm
Opening on the puller housing : 100mm
Max. pressure range : 118mm br> Drive : 20mm br> Suitable for impact wrenches.

Suzuki Suspension Castle Nut Socket
4 Pin / 1/2in.Dr Socket
External 43mm / Internal 30.5mm
Pins : 5mm x 6.3mm
Applicable to : V650 / 1000 | DI650 / 1000 | V-Storm
Also Hayabusa / Bking and GSX-R750 / 1000 / 1100

13mm Suspension Top Mount Nut Wrench
for VAG - Audi | Seat | Skoda | VW
13mm 6 / 8 point Dual Sided Swivel Socket
120mm Total Length with 3/8in.drive.
Specialist tool designed to be used when
removing the top of Macpherson strut mounts.
Flexible for hard to reach parts allowing access
to the strut mount with minimal effort due to the flexible design.

Electric Brake Fluid Bleeder
For most makes and models of vehicles
With Adjustable pulse oil change which can effectively
clean the pipeline and change the oil more thoroughly.
Contents : Brake Fluid Bleeder / 2L Bottle & 3.5M Hose / 3 Adaptors.
Power supply : 240V | 50 / 60Hz | 35W
Output Pressure : 0.6 - 3.0 Bar
Output flow : <= 1.2L / Min
Noise Level : 70 Db
Device shuts off when container is empty

Dial Test Indicator & Precision Point Set
0 - 10mm Dial in 0.01mm increments.
Magnetic base with fine adjustment.
Magnet has a 60kg pull.
On / Off Switch for easy positioning.
Used to check variations in machined parts.
Ideal for checking run-out on disc brakes.

Bearing Puller Kit with Ball Ended Puller Adaptor
Suitable for removal of a variety of blind bearings
where traditional bearing and gear pullers will not reach.
Ball-end tips fit inside bearing races to provide traction for bearing extraction.
Bearing Sizes : 5 / 6 / 8 / 9 / 11 / 12.5mm

Universal Wheel Bearing Spreader
Designed to separate the suspension strut from the wheel bearing housing.
Spreading range : 5.0 - 11.5mm
Drive : 17mm Hex

68mm Bearing Inner Ring Puller
For removing the inner wheel bearing rings on wheel hubs.
The bearing rings usually remain on the wheel hub
when the wheel bearings are removed.
Integral Clamp holds the puller legs
securely behind the component to be removed.
Pressure piece diameter : 25 x 30mm
Puller width : 68mm
Puller depth : 60 mm